Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 34

Страница: 34 / 122

03TA Service Manual

INSTALLING YOUR TUBE-ICE

MACHINE

4/2/14

3-12

Ice Machine Model

03TA (Standard)

03TA (High Ambient)

Electrical Frequency, Hz.

60/50

Recommended Condenser

BNHS02A011

BNHS02A011(12)

Total Heat Rejection (BTU/hr)

157,500 / 144,900

172,500 / 159,700

Fans:
   Number
   HP, Each
   Total CFM

1 1/2

20,500

Full Load Amps (FLA):
   3 ph., 208/230V, 60 hz.
   3 ph., 460V, 60 hz.
   3 ph., 200V, 50 hz.
   3 ph., 380V, 50 hz.

14.0

7.0

14.0

7.0

Weight, lbs.:
   Net
   Shipping
   Operating (Maximum flooded) R-404a

580
760
610

585
765
615

Condenser Dimensions, inches

(See Fig. 3-7)

   A  (Width)
   B  (Length)
   C  (Height)
   D  (Leg centerline)
   E  (Leg centerline)
   F  (Clearance below)

45.46”

127”

49.15”

38”

106.15”

20.5”

Recommended Line Sizes, OD
   Liquid
      All lengths and orientations
   Discharge Gas
      Vertical Up, all lengths
      Horiz. or Down, < 75 ft.
       Horiz. or Down > 75 ft.

7/8”

1 1/8”
1 1/8”
1 3/8”

Connections at Condenser:
   Liquid (ODV)
   Discharge Gas (ODV)
Connections at Ice Machine:
   Liquid (ODV)
   Discharge Gas (ODV)

1 1/8”
1 3/8”

1 1/8"
1 1/8"

TABLE 3-4

Air-Cooled Condenser Data

Содержание TUBE-ICE 03TA



























































































































Результаты поиска

Содержание TUBE-ICE 03TA

Отзывы:

Vogt TUBE-ICE 03TA, Руководство по обслуживанию, Страница: 34 / 122

Результаты поиска

Содержание TUBE-ICE 03TA

Отзывы: