Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 122

Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 72

03TA Service Manual

MAINTENANCE

3/31/14

7-10

Note To Manager or Owner:

This page is a complete Preventive Maintenance Schedule that should be performed each 90 days.
The Preventive Maintenance page may be copied and given to your service person. It should be
signed, dated, and returned to you for permanent record.

Preventive Maintenance Program

This form can be removed and duplicated for keeping accurate records.
Model # ___________________

Serial # ____________________

Date _____________

Customer/Address ___________________________________________________________

____________________________________________________________

Mgr. Name ______________________  Service Tech Name __________________________
The following service performed and checked:
_____  Last maintenance performed (approx. date)
_____  Scale condition of water tank & tubes (good - fair - poor)
_____  All drains freely draining (water tank, drip pan, ice bin)
_____  Water distributors cleaned
_____  Ice machine cleaner circulated through system
_____  Condenser clean (if applicable)
_____  Voltage at machine (actual reading) ________, ________, ________
_____  Compressor amps (halfway through the freeze cycle) ________, ________, ________
_____  Cutter motor amps (cutting ice) ________, ________, ________
_____  Water pump amps ________, ________, ________
_____  AC condenser motor amps (if applicable) ________, ________, ________
_____  Crankcase heater heating
_____  Refrigerant leak (okay - high - low)
_____  Leak checked system ______ leaks found & repaired
_____  Compressor oil level (i.e., 1/4 - 1/2 - 3/4 - low - high)
_____  Gear reducer oil (okay - low)
_____  PSIG, low pressure switch set @
_____  PSIG, high pressure switch set @
_____  Bin stat(s) installed and operating properly
_____  Make-up water float valve adjusted okay
_____  Adjustable blowdown adjusted for clear ice
CYL__________

CRU________

Suction PSIG at end of freeze

CYL_____/____

CRU____/____

Suction PSIG during harvest (high/low)

CYL__________

CRU________

Discharge PSIG at end of freeze

______

°

F/

°

C at machine

______

°

F/

°

C outside ambient (at condenser if applicable)

______

°

F/

°

C make-up water temperature

_____  Freeze cycle time (minutes)
_____  Harvest cycle time (minutes)
_____  First ice out (seconds)
_____  All ice out (seconds)
_____  Pounds of ice per cycle
Capacity check:   ice weight per cycle

X 1440 = _________ lbs. (24 hr. capacity)

total cycle time (min) _____

Remarks:_________________________________________________________________________

_________________________________________________________________________________

«
...
70
71
72
73
74
...
»

Содержание TUBE-ICE 03TA



























































































































Отзывы:

Нет отзывов