Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 122

Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 87

03TA Service Manual

SERVICE OPERATIONS

4/11/14

9-5

Air-Cooled Units.

The condenser fan switch mounted to the frame (lower right side) (FIGURE 9-

5B) (CPS) is used to regulate the head pressure.  This is an adjustable pressure switch located on the
right-hand  front  of  machine.    It  controls  the  operation  of  the  condenser  fan  motor(s)  through  a
contactor  (FC)  (FIGURE  6-2)  located  in  the  control  panel.    The  switch  is  set  to  cycle  the  fan
motor(s) “On”  at 210 psig  and  “Off”  at 190 psig for R-22  and “On” at 250 psig and “Off” at 230
psig for R-404a.  Higher settings may be necessary for 0

°

F and below ambient conditions to assure

there is enough warm gas for ice harvesting.

Oil Separator.

A coalescent oil separator is used to separate the oil from the discharge gas and return

it to the compressor

FIGURE 9-6

Oil Separator

Line to condenser

Vogt Part #:

Adjusting Stem

Set at 200 PSI (R-22)

Set at 235 PSI (R-404A)

(CW Lowers Setting)

1 1/4” FPT Connection

(water connections)

Connected to High Side of

Water Cooled Condenser

Vogt Part #:

Cut In Adjusting Screw

Set at 210 PSIG (R-22)

Set at 250 PSIG (R-404A)

(CW Lowers Setting)

Cut Out Adjusting Screw

Set at 190 PSIG (R-22)

Set at 230 PSIG (R-404A)

(CW Raises Setting)

Connected to

Compressor Discharge

FIGURE 9-5A.

Water Regulating Valve

FIGURE 9-5B.

Condenser Fan Switch

Replacement filter

Vogt Part #:

Gasket – supplied with filter

Temprite Oil Separator
Vogt Part #:

(Add 16 ounces of oil when installing
new or after changing filter)

AC&R Oil Separator
Vogt Part #:

(Add 12 ounces of oil when
installing new separator)

Oil return line to

compressor

Discharge line from

compressor

Line to condenser

Discharge line from

compressor

Oil return line

to compressor

«
...
85
86
87
88
89
...
»

Содержание TUBE-ICE 03TA



























































































































Отзывы:

Нет отзывов