Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 51

Страница: 51 / 122

03TA Service Manual

START-UP AND OPERATION

3/31/2014

5-3

! CAUTION !

The crankcase heater should be energized for a MINIMUM of

2 hours and the crankcase must be free of liquid before

attempting to operate the compressor.

! CAUTION !

FIGURE 5-1

Bottom Portion of Control Panel

Start-Up Procedure

Starting the machine in freeze mode:
(NOTE: to start in harvest mode, turn “Clean/Off /Ice selector switch to “Ice” and press “Start”)

1.

Set the “Clean/Off/Ice” selector switch to the “Clean” position.

Push the “Start” button to start the water pump.

The pump can be stopped and started by the “Stop” and “Start” push buttons to purge the

tubing of air.

When there is good water flow, turn the “Clean/Off/Ice” switch to “Ice”. The machine will

then start in a harvest (thaw) period with the compressor running.

At the termination of the harvest period, the machine will begin the freeze period.

NOTE: Be sure to observe several cycles of ice production to confirm the satisfactory
operation of the machine.

Complete the remaining part of the “Warranty Registration/Start-Up Report” and return it to

the Vogt Ice LLC.

CONTROL PANEL DOOR)

Stop

Start/

Manual

Harvest

Clean Ice

Off

Содержание TUBE-ICE 03TA



























































































































Результаты поиска

Содержание TUBE-ICE 03TA

Отзывы:

Vogt TUBE-ICE 03TA, Руководство по обслуживанию, Страница: 51 / 122

Результаты поиска

Содержание TUBE-ICE 03TA

Отзывы: