Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 122

Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 69

03TA Service Manual

MAINTENANCE

3/31/14

7-7

Vent Plug

Drain Plug

Oil Level Plug

Vent Plug

Compressor

HP

Oil Charge

(oz)

3DE3R & 3DEHR

6.5

125

3DP3R & 3DPHR

7.5

125

TABLE 7-3

Compressor Oil Capacity

An oil pump should be used to force any oil that may be required into the system.  Oil may be added
to the compressor through the low pressure test connection adjacent to the high/low pressure switch
or  through  the  compressor  suction  service  valve.    The  compressor  suction  service  valve  should  be
“backseated”  to  shut  off  pressure  to  the  gauge  port  when  connecting  the  oil  pump.    Air  should  be
purged from the oil pump discharge line by forcing some oil through the line before tightening the
charging connection.

Cutter Gear Reducer.

The oil level for the gear reducer should be checked if there is evidence of a

leak. It should be level with the plugged opening in the side of the gear housing. Use Mobile 600W
cylinder oil or equal. Change oil once a year.

Note: Ventless gear reducer used after August 2010

FIGURE 7-2

Gear Reducer

Gear Reducer (10:1)
Part #:

Replacement food grade oil:

Part #: 19T3020C01

Texaco Cygnus 220

Oil Capacity: 8 ounces

«
...
67
68
69
70
71
...
»

Содержание TUBE-ICE 03TA



























































































































Отзывы:

Нет отзывов