Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 122

Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 21

03TA Service Manual

RECEIPT OF YOUR TUBE-ICE MACHINE

3/31/14

2-1

2. Receipt Of Your Tube-Ice Machine

! WARNING !

Only service personnel experienced in refrigeration and qualified

to work with high voltage electrical equipment should be allowed

to install or work on this Tube-Ice

®

machine.

! WARNING !

Inspection

As soon as you receive your machine, inspect it for any damage. If damage is suspected,

note it on the shipper’s papers (i.e., the trucker’s Bill of Lading). Immediately make a separate
written request for inspection by the freight line’s agent. Any repair work or alteration to the
machine without the permission of Vogt Ice



, LLC can void the machine’s warranty.

The machine was shipped with a full charge of refrigerant stored in the receiver. Visually check all
lines for mechanical damage. If a leak is suspected, check all joints with a Halogen Leak Detector.
All leaks should be reported to Vogt Ice



, LLC to obtain authorization for repair.

! CAUTION !

The approximate weight of the machine is 2000 pounds. Always use

equipment with adequate load carrying capacity.

! CAUTION !

The machine frame has lifting lugs at each corner in the top for eyebolts and hooks to be used for
lifting purposes if desired. Lifting lugs should be used whenever possible.

! CAUTION !

The Tube-Ice

®

machine is top heavy.

Secure to avoid tipping.

! CAUTION !

If a forklift is used, make sure its capacity is sufficient. The forks must be wide enough apart to
prevent tipping sideways and must extend beyond the extremities of the frame base structure. The
machine needs to be bound in place to prevent tipping.

Safety Valves

Safety pressure relief valves are an integral part of the packaged Tube-Ice

®

machine.

One is located in the low-side of the system on the freezer, one is in the high side of the system on
the receiver, and one is on the condenser. Vent each of the pressure relief valves to the atmosphere
in such a manner as to comply with local and national codes.

Machine Room

The machine must be located inside a suitable building and must not be subjected to

ambient temperatures below 50

°

F (10

°

C) or above 110

°

F (43.3

°

C). Heat from other sources

(sunlight, furnaces, condenser, etc.) and unusual air currents may affect the operation of the machine
and should be avoided. The electrical components of the Tube-Ice

®

machine are rated NEMA 1.

Therefore, the machine should not be located in a hazardous area or sprayed with water. The
machine should be installed on a drainable condensate drip pan or in an area where water will not
stand but will readily drain away from the machine. See Space Diagram for clearances and utility
connections, FIGURES 3-4A,3-4B and 3-5.

«
...
19
20
21
22
23
...
»

Содержание TUBE-ICE 03TA



























































































































Отзывы:

Нет отзывов