Versalift 24 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 54

background image

This Messinine install shows the ceiling
Cover Underneath. (above)

PHOTO SHOWING INSTALLER PULLING DOWN ON SPRING LOADED CEILING COVER. As the lift goes up through the
opening, the cover catches on the ceiling allowing the springs to hold it tight.

Lift shuts off automatically up and down.

Q. HOW DOES THE LIFT GET LEVEL WITH MY ATTIC FLOOR???

A. There are Four Springs in each of the legs of the Basket that travels Into your attic. The Ceiling Panel closes on the
garage ceiling sheetrock, and the lift continues to travel up through the opening until it is Level with the Attic Floor, at
which time it automatically shuts off. These springs will allow for 20

” depth.

Thus we don’t care if you have 2 x 8’s, 2 x

12’s, or 18” “I” joists, the spring will stretch and hold the cover tight against the ceiling. You can also apply some foam

insulation tape to the lift door to seal it off from really cold climates. You could also drape a blanket or cover over the
lift when in up position to protect the attic or garage from cold air.

«
...
6
7
8
9
10
...
»

Содержание 24























































Отзывы:

Нет отзывов

Похожие инструкции для 24

Бренд: G-Technology Страницы: 32

Бренд: G-Technology Страницы: 35

FlashPen "Piko"

Бренд: Hama Страницы: 8

Tenus FlashPen USB 3.0

Бренд: Hama Страницы: 4

Solid Stainless Steel Shelving

Бренд: Omega Страницы: 2

Бренд: WiebeTech Страницы: 4

Бренд: Edirol Страницы: 1

HAWK 2 ST11900W

Бренд: Seagate Страницы: 40

Бренд: Seagate Страницы: 54

Бренд: Dorel Asia Страницы: 15

Бренд: Sans Digital Страницы: 2

Бренд: LaCie Страницы: 26

Cloud Object Storage System Slicestor 2212...

Бренд: IBM Страницы: 50

Бренд: Lowrance Страницы: 32

Бренд: iStorage Страницы: 23

Бренд: LevelOne Страницы: 85

Бренд: morse Страницы: 8

HUS151414VL3600

Бренд: Hitachi Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды