Versalift 24 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 54

Versalift 24 Скачать руководство пользователя страница 9

Q.

Can you give me any details on the Lifting Cables for the Versalift?

A. The two cables have a lifting strength of 1,000 lbs. per cable.
They are .093 Aircraft steel Cable 7 x 19 (which means 7 bundles of
19 woven filaments for 132 strands. Safe working rating is 350 lbs.
We rate the Model 24 lift at 200 lbs. and the Model 32 at 250 lbs.
for safety purposes.

The LIFT DECK is

20 ¾” x 44” Outside Dimensions and made of ¾” Plywood press board that is covered in Melamine

construction material.

Melamine resin is the main constituent of high-pressure

, such as

and

laminate flooring

. Melamine

is

used typically used as the binder / resin in hard-surface countertop materials, such as those used in lab desks.

Q. What happens if I mis-measured, and when the unit gets here the cables are not long enough?

A.  You will need to ship back the entire control head unit in the original box that it came in.  Call us first and get a RGA
Number.    The cables are installed at the factory, and it is specially designed stainless steel aircraft cable that has to be
installed properly.

«
...
7
8
9
10
11
...
»

Содержание 24























































Отзывы:

Нет отзывов