Versalift 24 Скачать руководство пользователя страница 51

Страница: 51 / 54

IMPORTANT: DO NOT USE A POWER TOOL TO INSTALL THE CABLE CLAMP NUTS. USE ONLY A WRENCH OR
A SOCKET AND RATCHET! THESE NUTS MUST BE TIGHTENED TO THE SPECIFIED TORQUE ONLY!

Versa Lift

ASSEMBLY GUIDE

(All Models)

Fig. 29

Fig. 30

Fig. 31

Fig. 32

7. DO NOT CUT CABLE.
STORE EXCESS AS SHOWN
OR ROLL UP AND ZIP TIE
TO INSIDE OF THIS FLANGE.

REPEAT FOR OTHER END.

3. PASS CABLE THRU SLOT IN

BRACKET AS SHOWN. THEN
PULL SLACK OUT OF CABLE.

1. DROP THE CABLES

DOWN THROUGH

THE LIFT OPENING.

6. TIGHTEN LOCKNUTS
TO SPECIFIED TORQUE

OF 5 FOOT POUNDS
(or SNUG + ½ TURN).

DO NOT OVER-TIGHTEN!

1/4-20

LOCKNUT (10)

5. PULL FIRMLY

HERE UNTIL CABLE

CLAMP IS IN PLACE &

NUTS ARE TIGHT TO
SPECS (SEE BELOW).

1/2 x 3/8" Aluminum

SPACERS (10)

CABLE

CLAMP (2)

4. WIND THE CABLE

TIGHTLY ON THE

STUDS EXACTLY

AS SHOWN HERE.

2. PLACE THE LIFTING

PLATFORM ON THE
FLOOR DIRECTLY UNDER

THE LIFT OPENING.

Versa Lift

Installation - Assembly

(All Models)

Содержание 24























































Результаты поиска

Содержание 24

Отзывы:

Похожие инструкции для 24

Бренды по названию

Популярные бренды

Versalift 24, Руководство пользователя

Результаты поиска

Содержание 24

Отзывы:

Похожие инструкции для 24

Бренды по названию

Популярные бренды