Versalift 24 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 54

background image

Attic Storage Lifting System

IMPORTANT NOTE:

The required finished opening is 22.5 x 46.5”
with smooth sidewalls. Whenever joist hanger
brackets are used to frame the opening, they
must be covered to prevent interference with
the lifting platform operation. 2 x 2” “L” shaped
flashing strips (4) are provided by BPG to cover
hanger brackets and nail head in the corners
of the lift opening.

IMPORTANT NOTE:

The required finished opening is 22.5 x 46.5”
with smooth sidewalls. Whenever joist hanger
brackets are used to frame the opening, they
must be covered to prevent interference with
the lifting platform operation. 2 x 2” “L” shaped
flashing strips (4) are provided by BPG to cover
hanger brackets and nail head in the corners
of the lift opening.

Revised 06-12-2008

CAD:

24RUFN-16-PLAN.DWG

RUFN-FRT .DWG

CAD:

24

-X

RUFN-SIDE .DWG

CAD:

24

-X

Roughing-In Notes:

Tolerance for opening dimensions is +1/4” (6mm), -0” (-0mm).
The opening must be square and the side walls perpendicular.
Maximum joist height is 18” tall. See specification sheet for
maximum floor-to-floor height of specific models. For detailed
framing suggestions, see the

Versa Lift Installation Guide

.

TYPICAL FRAMING FOR

24” O.C. SOLID JOISTS

TYPICAL FRAMING FOR

16” O.C. SOLID JOISTS

Rough-In Guide for
Solid Lumber Joists

Applicable Product Models:

24, 24H, 24HX, 24W, 24WH, 24WHX

RUFN-24-PLAN.DWG

CAD:

24

«
...
10
11
12
13
14
...
»

Содержание 24























































Отзывы:

Нет отзывов

Похожие инструкции для 24

Бренд: Quest Engineering Страницы: 540

TotalStorage DS300

Бренд: IBM Страницы: 110

System storage DS6000 Series

Бренд: IBM Страницы: 298

System storage DS6000 Series

Бренд: IBM Страницы: 58

Бренд: IBM Страницы: 78

Бренд: Kanguru Страницы: 17

XCubeNAS XN7012R

Бренд: Qsan Страницы: 16

Бренд: DANE-ELEC Страницы: 2

Бренд: Hamlet Страницы: 10

05DTMBAX0307DD-V1

Бренд: Mercia Garden Products Страницы: 9

Бренд: Maxtor Страницы: 50

Бренд: V-TAC Страницы: 28

Бренд: Lifetime Страницы: 52

Бренд: Newpo Страницы: 5

Бренд: Archos Страницы: 12

Бренд: Oracle Страницы: 268

Store n Go series

Бренд: Verbatim Страницы: 2

Бренд: Black Box Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды