WARNING
!
K
!
e
n
e
re
p
d
o
il
ut
ch
of
of
reach
T
!
u
e
rn
s
L
u
ift
in
of
ot
f when n
19
Versa Lift
Remote & Receiver
(Wireless Models)
MODE
CH 2
CH 2 DIP
(DOWN)
CH 1 DIP
(UP)
CST MNT
CH 1
MODE
MNT
CST
1 2 3 4 5 6 7 8
10
9
ON
ON
9 10
8
7
6
5
4
3
2
1
12V
24V
P3
CONFIG
SWITCH
STAN
MULTI
LINEAR
CONFIG
SWITCHES
10
10
CH 1 DIP
(UP)
CH 2 DIP
9 VOLT
(DOWN)
BATTERY
1 2 3 4 5 6 7 8 9
ON
ON
9
8
7
6
5
4
3
2
1
STAN
MULTI
LINEAR
MULTI
LINEAR
STAN
1 2 3 4 5 6 7 8
10
9
ON
ON
9 10
8
7
6
5
4
3
2
1
CH2 N/O
LINEAR
MULTI
STAN
24VAC/DC
CH1 N/O
P3
24V
12V
1 2 3 4 5 6 7 8
10
9
ON
ON
9 10
8
7
6
5
4
3
2
1
CH 2
MODE
CST MNT
MODE
CH 1
MNT
CST
(UP)
CH 1 DIP
(DOWN)
CH 2 DIP
WAR
NING
!
Kee
en!
p ou
t
childr
of reac
h of
Turn
se!
Lift o
f
not in u
f whe
n
CHANNEL 2 DIP
SWITCHES MUST
BE SET ALIKE
CHANNEL 1 DIP
SWITCHES MUST
BE SET ALIKE
NOTE: CHANNEL
1 & 2 DIP SWITCHES
MUST BE SET TO
DIFFERENT OR
OPPOSITE COMBOS
ALL THREE
CONFIGURATION
SWITCHES MUST
BE SET ALIKE
RADIO
RECEIVER
REMOTE
TRANSMITTER
12. WIRELESS REMOTE SETTINGS & OPERATION
The wireless receiver and remote transmitter are pre-set at
the factory to the codes and configurations shown below. A
9-volt battery will also be installed in the transmitter at the
factory. If your transmitter fails to operate the lift, first make
sure the lift power cord is plugged in and the power switch
on the rear of the motor housing is turned ON and lighted.
If the transmitter still fails to operate the lift, replace the
battery with a fresh 9-volt battery. The indicator light at the
top of the transmitter when either the up or down button is
pushed and a signal is being transmitted. See the Owners
Manual for details about operation of the remote transmitter.
13. CHANGING CODES & CONFIGURATION SETTINGS
Normally you will not need to change the factory settings
unless someone within a block of you is operating a Versa
Lift wireless model too or you are getting interference from
some other radio frequency device, tower, or broadcasting
station nearby. If so, first try changing the configuration
switch settings on both devices to “LINEAR” or “STAN.”
This will most likely correct the problem. If not, you can
change the codes on the dip switches (see below). Do not
use these codes: All 10 positions ON; All 10 positions OFF;
Alternating ON/OFF; Alternating OFF/ON. Use a random
code combination and follow the rules below.
Read and understand the Owners Manual completely before operating this lift!
There are IMPORTANT SAFETY FACTS THAT YOU MUST KNOW BEFORE USING THIS PRODUCT!
WARNING
!
DON’T CHANGE THE
JUMPER SETTINGS!
(405) 516 2412
