Versalift 24 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 54

Versalift 24 Скачать руководство пользователя страница 27

Fig. 25

DOOR BRACE (2)

SCREW
COVER (6)

Assemble

Close

Screw Cover

10-32 x 7/8"

PHILLIPS
SCREW (6)

DOOR PANEL (1)

10-32
LOCKNUT (6)

15

Versa Lift

ASSEMBLY GUIDE

(All Models)

Fig. 26

Fig. 27

INSERT SUPPORT
INTO LEG. ALIGN

TO FIRST HOLE.

PLATFORM
PANEL (1)

NOTE: SECOND (INSIDE)
HOLES ARE NOT USED.

1/4-20 x 2"
CARRIAGE
BOLTS (4)

1/4x5/8" WASHER (4)

1/4-20 LOCKNUT (4)

PLATFORM
SUPPORT (2)

PLATFORM
LEG (2 LEFT)

PLATFORM

LEG (2 RIGHT)

RECESSED
HOLE S UP

PLATFORM
SUPPORT

PLATFORM
LEG

1/4x5/8" WASHER (4)

1/4-20 x 1- 1/2"

HEX BOLT (2)

PLATFORM

TOP BRACE

1/4-20

LOCKNUT

(2)

PLATFORM LEG
BRACKET (2)

1/4 -20 x 1-1/2"
HEX BOLT (8)

1/4 x 5/8" WASHERS (16)

1/4-20 LOCK-

NUTS (8)

5. DOOR ASSEMBLY

The door must be

down-stairs. Locate the

door, door braces, and fasteners shown in Fig. 25.
Insert the screw through the screw cover then through
the panel, then through the door brace (Fig. 25 and
inset). and fasten with the locknut. Tighten all 6 screws,

assembled

then close the screw covers, Make sure they snap
completely shut (Fig. 25 inset).

6. PLATFORM ASSEMBLY

The platform must be assembled down-stairs. Locate the
platform, 2 platform supports, 4 platform legs, carriage
bolts, washers, and locknuts (Fig. 26). Note that the top
side of the platform has recessed holes. Insert the
platform support into one of the left legs as shown (Fig.
26 inset). Align the hole in the leg with the hole in the
outer end of the support. Next insert a carriage bolt down
through the platform, leg and support (Fig. 26). Secure
with a washer and locknut, but do not tighten until all four
bolts are installed. When all legs are assembled as
shown in Fig. 26, tighten all of the bolts and locknuts, but
do not over-tighten or you will collapse the tubing.

Locate the platform leg brackets, platform top brace, and
fasteners. Install each of the brackets with 4 bolts,
washers, and locknuts (Fig. 27 inset). Tighten as above.
Install the platform top brace with 2 bolts, washers and
locknuts (Fig. 27) and tighten fasteners as above.

«
...
25
26
27
28
29
...
»

Содержание 24























































Отзывы:

Нет отзывов