manualshive.com logo in svg

Vedeneyev M-14P, Руководство по обслуживанию

Мы предлагаем скачать бесплатно Руководство по техническому обслуживанию Vedeneyev M-14P на нашем сайте. Этот мануал поможет вам правильно ухаживать за вашим двигателем, обеспечивая его долгую и безотказную работу. Не забудьте загрузить его с manualshive.com.

Поделиться
Скачать
background image

 

162 

(12) Using a syringe, fill 150 to 200 g of oil K-17 heated to a temperature of 40 °C into each cylinder 

through the spark plug holes with the piston being at the BDC turning the airscrew shaft for 3 to 4 turns, then 
refill the oil into the cylinders without turning the airscrew shaft. Fill the oil using a syringe with a special tip. 
Turn the shaft with the compressor inlet valve being depressed. 

(13) Brain oil K-17 from the engine crankcase through the oil sump drain cock. 
(14) Remove excessive oil from the cylinders through the spark plug holes using a syringe, then drive 

plugs or spark plugs into the spark plug holes. 

Install covers with paraffined paper gaskets on the cylinder exhaust ports. 
(15) Install caps on the fuel pump connections and stop the compressor delivery valve. 
(16) Preserve the magneto internally using the following procedure: 
(a) Drive out four pipe attachment screws, remove the shield and distributor taking care not to 

damage the high-tension terminal socket and the central electrode. 

(b) Clean the cam, coupling bolt crown nuts, breaker mechanism parts of soil. Clean these parts with 

chamois or coarse calico cloth slightly moistened in clean alcohol. 

(c) Wrap the cam profile working surface with one layer of calico or tafetta tape,  . (16^2) mm wide, 

(140^2) mm long, 0.2 to 0.3 mm thick, impregnated with gun grease or grease PVK heated to a temperature 
of 105 to 110 °C. 

(d) Using a brush, coat the breaker spring and arm with a thin layer of turbine oil T22, avoiding runs. 

CAUTION:

 AFTER INSTALLING THE COVER ON THE COMPRESSOR DELIVERY VALVE AND 

PRESERVING THE MAGNETO, NEVER TURN THE ENGINE AIRSCREW SHAFT. 

(e) Reinstall the removed parts, seeing to it that the distributor, high-tension terminal socket, central 

electrode and the shield are properly arranged. 

(17) Preserve the generator, using the following procedure: 
(a) Wash the generator shank and flange with gasoline Nefras-S 50/170 or BR-1, BR-2. 
(b) Make sure there are not traces of corrosion. If corrosion is detected, remove it with sandpaper No. 

230 moistened in oil. 

(c) Lubricate the casing, shank, flange, heads of screws and bolts securing pole shoes and terminals 

with oil K-17, avoiding getting of lubricant inside the generator. 

(d) Wrap the generator in paraffined paper and pack in a separate box.(18) Remove the engine from 

the support, place it on the bottom of the packaging container and. secure by braces using the following 
procedure: 

(a) Uncotterpin and undo six nuts (2) (Ref. Fig. 402) of the engine frame ring. 
(b) Remove six washers (3) and (1) each. 
(c) Install three shipping brackets instead of the removed washers. 
(d) Install six nuts (2) on the engine frame studs, tighten and cotterpin them. 
(e) Install the braces and secure them to the container bottom. 
(19) Perform external preservation of the engine and its accessories using the following procedure: 
(a) Wipe the engine with a cloth moistened in gasoline Nefras-S 50/170 or BR-1, BR-2 and blow with 

compressed air. See to it that gasoline does not get inside the engine, in the thrust bearing and rubberized 
fabric hoses of the tappet 

rod casings. 
(b) Inspect the engine and touch up having degreased the damaged paintwork spots with gasoline. 

Use a spray gun or a brush to touch up. 

NOTES: 1. Touch up the damaged engine surfaces painted khaki with epoxy enamel EP-140, 

the surfaces painted black, with black nitrocellulose varnish ITTs-286. To obtain the required color it 
is allowed to add up to 30 % black enamel ?-163 to nitrocellulose varnish NTs-286. 

2. Touch up the silver color accessories with aluminium powder nitrocellulose varnish. 
3. Dry the engine after touch up for 30 to 60 min at a temperature of 10 to 30 °C, protecting the 

touched up areas against grease at external preservation of the engine. 

(c) Remove the fine fuel filter and its pipelines from the airplane. Perform internal preservation of the 

filter with oil MS-20 heated to a temperature of 60 to 70 °C. Do not subject the fine fuel filter to external 
preservation. 

(d) Coat non-painted steel parts of the engine and its accessories with oil K-17 (the painted parts may 

be left unpreserved). 

(e) Generously coat the airscrew shaft end with oil K-17, attach the shackle to it, wrap with two or 

three layers of paraffined paper and fix with twine. 

(20) Wrap the engine with 2 or 3 layers of paraffined paper, secure with twine which should not touch 

the unpreserved places. 

Содержание M-14P






























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M-14P

Jabiru 3300 Instruction And Maintenance Manual preview
3300
Бренд: Jabiru Страницы: 103
Kohler CH-11-16 Owner'S Manual preview
CH-11-16
Бренд: Kohler Страницы: 84
Regal 26-2215 User Manual preview
26-2215
Бренд: Regal Страницы: 32
Danfoss EM-PMI375-T200 User Manual preview
EM-PMI375-T200
Бренд: Danfoss Страницы: 77
Briggs & Stratton 40G700 Series Illustrated Parts List preview
40G700 Series
Бренд: Briggs & Stratton Страницы: 20
Man D2842 LE602 Operating Instructions Manual preview
D2842 LE602
Бренд: Man Страницы: 50
Aerotech High-Power RMS-PLUS 54/1706 Assembly And Operation Instructions preview
High-Power RMS-PLUS 54/1706
Бренд: Aerotech Страницы: 2
Aerotech RMS 98/10240 BLACK MAX Assembly And Operation Instructions preview
RMS 98/10240 BLACK MAX
Бренд: Aerotech Страницы: 2
Saito FG-60R3 Instruction Manual preview
FG-60R3
Бренд: Saito Страницы: 2
Saito FG-14C Instruction Manual preview
FG-14C
Бренд: Saito Страницы: 2
Saito FG-21 Instructions Manual preview
FG-21
Бренд: Saito Страницы: 7
Festo EMMS-ST-28-L Series Operating Instructions preview
EMMS-ST-28-L Series
Бренд: Festo Страницы: 4
Raider 50 HP TLDI Owner'S Manual preview
50 HP TLDI
Бренд: Raider Страницы: 28
ARRI cforce plus User Manual preview
cforce plus
Бренд: ARRI Страницы: 28
Greyhound 96156 Installation, Operating And Servicing Instructions preview
96156
Бренд: Greyhound Страницы: 19
Detroit Diesel DD15 EuroIV Operator'S Manual preview
DD15 EuroIV
Бренд: Detroit Diesel Страницы: 116
Detroit Diesel MBE 900 Operator'S Manual preview
MBE 900
Бренд: Detroit Diesel Страницы: 158
Detroit Diesel 60 Operator'S Manual preview
60
Бренд: Detroit Diesel Страницы: 172

Бренды по названию

Популярные бренды

Загрузить еще бренды