![background image](http://html1.mh-extra.com/html/vedeneyev/m-14p/m-14p_maintenance-manual_3767467118.webp)
131
TO M-14P M.S.
TASK CARD No. 260
M S ITEM
074.10.01b
procedure: Accomplishment of Magneto Scheduled Maintenance according to Magneto Maintenance
Manual
OPERATIONS AND TECHNICAL REQUIREMENTS
CORRECTIVE
ACTIONS
CH
ECKED BY
1. Drive out three magneto shield attachment screws. 2. Drive out four magneto pipe
attachment screws.
3. Remove the distributor and carefully move it aside so as not to damage high-tension
cable.
4. Carry out the following operations to check operability of the magneto assemblies.
(1) Check all screw joints of the breaker. T.R. Breaker screw joints should be reliably
tightened.
(2) Check rotation of the breaker mechanism arm on its pivot. T.R. The arm should rotate
smoothly without jamming.
(3) Measure the breaker contacts gap (Ref. 074.10.01, Task Card STo. 203). T.R. The
gap should be from 0.25 to 0.35 mm.
(4) Burnish the contacts in case of soiling or oiling, wipe them with chamois or clean cloth
moistened in clean alcohol.
T.R. Oiling and soiling of contacts are not allowed.
(5) Adjust the gap to be from 0.25 to 0.35 mm (Ref. 074.10.01, Task Card No. 203).
NOTE: Make an entry in the magneto Certificate after each adjustment of breaker
contacts.
Tighten loosened screws
of breaker mechanism
Eliminate jamming of arm
on its pivot
Adjust gap to be from
0.25 to 0.35 mm
Burnish and wipe
contacts
Содержание M-14P
