Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 138

background image

Instructions and settings

60

27.06.2011

ver. 2

Low-lift/Full lift

Use push-button

to switch between low-lift and full lift. The indicator lamps next to the

button show which function has been engaged. Use low-lift when drilling. This prevents the ma-
chine from being raised too much, while allowing proper operation of the following harrow in the
headland. Never reverse the machine in the low-lift position.

If it becomes necessary to raise the machine, e.g., when encountering an obstruction in the furrow

or to turn back and fill the seed hopper, be sure to first press

to disengage the auto advance

feature. Then press

to switch to full lift. The machine can now be raised to its maximum

height.

When the drill later is returned to the same position as before the interruption, press

to re-

engage auto advance of tramlining and bout marker switching, and press

to return to low-

lift operation.

The indicator lamp on the left of the button blinks when the low-lift switch has been engaged.

Lift stop

Use the lift stop when the bout markers should be retracted without lifting the machine from the

furrow, e.g., to pass a post or well. Press the button

and lift the bout marker using the hy-

draulic lever. Use

to alternate between low-lift and full lift. The control box remembers the

function that was engaged prior to activating the lift stop.

Tramlining

The selected tramlining programme is shown at the lower left of the display, while the current fur-
row in the sequence is shown at the lower right part.

Keep the button

depressed until the tramlining programme digit is selected. Then use the

selection dial to set the desired tramline interval (1 - 20) and confirm with

. Advance to the

desired start value using

. The lamps (6) light when tramlining is in progress.

Tramlining programmes 21 - 30 are special programmes used for lateral tramlining. See ”

Tramline options” on page 72

.

Tramlining programme 31 is used to enter a user-defined tramlining programme.

Keep the

button depressed until the tramlining programme number is marked. Select pro-

gramme 31 using the dial and confirm with

. In the left part of the menu, first select the de-

sired number of sequences in the tramlining cycle. Then use the right part of the display to select
in which sequences tracks should be made and whether they should be on the left and/or right. Ad-

vance to the desired start value using

.

«
...
58
59
60
61
62
...
»

Содержание Rapid RDA 400S











































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid RDA 400S

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: Labnet Страницы: 5

Бренд: Yardistry Страницы: 9

Бренд: FEAS Страницы: 72

Бренд: Bahco Страницы: 9

Бренд: B&G Страницы: 3

Бренд: Backyard Discovery Страницы: 51

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

The Wave Transformer

Бренд: EarthQuaker Devices Страницы: 21

Бренд: Harken Страницы: 4

Бренд: Harken Страницы: 2

TERRA FORCE BOOM

Бренд: Hardi Страницы: 40

Бренд: Harken Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды