Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 138

background image

Troubleshooting

120

27.06.2011

ver. 2

18 Seed fan, low rpm.

- Check that the hydraulic hoses have been correctly

connected to the tractor.

- Check whether the hydraulic oil flow from the tractor

has been correctly set.

- Check the alarm time limits that were programmed

into the Control Station.

- Check the cable, connectors and connections of the

rpm sensor.

- Check the function of the sensor by turning the fan

wheel by hand and also verifying that the sensor LED
lights. The LED should light when the pin on the fan
shaft passes. The distance between the sensor and the
pin should be 1 - 2 mm. Adjust if necessary. A lit
LED, however, is not necessarily any guarantee that
the sensor is operating.

See ”

5.16 Replacing the fan revolution sensor” on

, for replacement of the sensor.

- If the alarm is generated intermittently, a likely cause

is incorrect adjustment of the sensor or a defective
sensor.

19 Seed fan, high rpm.

- Check whether the hydraulic oil flow from the tractor

has been correctly set.

- Check the alarm time limits that were programmed

into the Control Station.

22 Seed output valve - max.

power.

- This valve, which controls the flow to the hydraulic

motor driving the seed output, opens fully.

- Check the oil flow from the tractor, the hoses and the

couplings.

- Check whether seed output is blocked or whether

there is another problem.

23 High voltage Workstation 1.

- The tractor supplies a voltage of more than 17 V. The

Control Station remains on, but certain functions,
such as electric motors and hydraulic valves, are
switched off.

24 High voltage Workstation 2.

- The tractor supplies a voltage of more than 17 V. The

Control Station remains on, but certain functions,
such as electric motors and hydraulic valves, are
switched off.

«
...
118
119
120
121
122
...
»

Содержание Rapid RDA 400S











































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid RDA 400S

ImageQuant LAS 4000

Бренд: GE Страницы: 86

Бренд: GE Страницы: 160

Бренд: GE Страницы: 134

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

Бренд: NEC Страницы: 29

Бренд: AAON Страницы: 36

Бренд: Abicor Binzel Страницы: 92

Бренд: LAWO Страницы: 459

Бренд: earline Страницы: 13

Бренд: VBM Страницы: 36

Бренд: W&H Med Страницы: 122

ActiveFinder One

Бренд: LaserLiner Страницы: 92

TRAKTOR KONTROL S4

Бренд: Native Instruments Страницы: 86

Бренд: Native Instruments Страницы: 245

Бренд: Samson Страницы: 2

Бренд: Jackson Страницы: 2

Бренд: Vag Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды