Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 26

Страница: 26 / 138

Instructions and settings

27.06.2011

ver. 2

3.7

Changing between transport position and working

position

3.7.1

Changing to working position

Figure 3.15

Lift the seed drill to its top position. Folding the wing sections in and out must always be car-
ried out with the seed drill fully raised. Also check that the tool bar is fully raised before folding
out.

Draw the wings together with the folding ram. At the same time unlock the wing sections with
the line.

Figure 3.18

Unfold the wing sections. Keep the lock release line taut until the second section has started to
unfold.

Figure 3.16

Figure 3.17

Содержание Rapid RDA 400S











































































































































Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды

Vaderstad Rapid RDA 400S, Оригинальное руководство пользователя

Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды