Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 138

background image

Instructions and settings

38

27.06.2011

ver. 2

3.14 Adjusting the following harrow

Figure 3.32

1 Select a suitable work angle from row of holes B.

2 The work pressure of the following harrow is adjusted using the adjusting screw (A). Depend-

ing on the work pressure set on the following harrow, the cotter (C) should be positioned be-
tween the trailing edge and centre of the oblong groove (D).

Adjust the following harrow to remain in the work position when turning on the headland in
the low-lift position. This will cancel out the tracks of the drill when turning.

Figure 3.33

3 Check that the following harrow tines trail in the between the wheel tracks and in the actual

wheel tracks, respectively. This indicates that the following harrow tines travel in the furrow
centre. When the following harrow tines travel between the furrows, high pressure can be ap-
plied on the following harrow without disrupting the seed.

In this fashion, a vaporization lay-

er can be harrowed while sowing.

NOTE!

Do not reverse the tractor unless the drill has been fully raised and the following harrow

has sufficient clearance height.

NOTE!

If the machine has been set to the maximum drilling depth and the following harrow is sub-

ject to a high load, the clearance in the transport position may be limited.

B

A

C

D

«
...
36
37
38
39
40
...
»

Содержание Rapid RDA 400S











































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid RDA 400S

Бренд: B&K Страницы: 12

Бренд: NEC Страницы: 54

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: Bahco Страницы: 9

MET ONE 3400 Series

Бренд: Hach Страницы: 48

Бренд: Jacto Страницы: 12

Бренд: Ironton Страницы: 6

Бренд: KCI Страницы: 2

Бренд: KCI Страницы: 60

Бренд: Landoll Страницы: 38

Бренд: ZacUrate Страницы: 2

Бренд: ZacUrate Страницы: 2

Бренд: Makita Страницы: 208

MOSQUITOTRAP MIE5

Бренд: Jata hogar Страницы: 20

NTP TECHNOLOGY DAD Thunder Core 256

Бренд: DAN Страницы: 16

Бренд: Mindray Страницы: 295

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды