Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 82

Страница: 82 / 138

Instructions and settings

27.06.2011

ver. 2

3.37 Maintenance of pneumatic brake system

3.37.1

Maintenance at the start of the season

Figure 3.90

1 Adjust the brake pads. Screw the adjustment screw (A) clockwise while rotating the wheels

slowly. Turn the adjustment screw until you feel resistance in the wheels as they rotate. This
means that the brake pads are in gentle contact with the brake drums.

When the adjustment screw is turned clockwise, the distance between the brake pads and the
brake drums decreases.

When the adjustment screw is turned counterclockwise, the distance between the brake pads
and the brake drums increases.

2 Check the oil level. Top up with new oil if necessary. Only use mineral oil type GL-4 or equiv-

alent.

NOTE!

The mineral oil should be type GL-4 or equivalent. Other types of brake fluid will damage

the system’s seals.

3 Check that all lines, hoses and brake cylinders are undamaged and that they are not leaking.

Содержание Rapid RDA 400S











































































































































Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды

Vaderstad Rapid RDA 400S, Оригинальное руководство пользователя

Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды