Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 88

Страница: 88 / 138

Advice on seeding and driving instructions

27.06.2011

ver. 2

4.6

Tramlining

The preparation of tramlines and setting of the Control Station are described in

”3.30.2 Func-

tions” on page 59

and

”3.32.2 Tramline options” on page 72.

During sowing, the most important thing to remember about tramlining is to shut off

Autostep

before doing anything other than normal sowing or turning in headlands between bouts.

So, remember to switch

Autostep

off before raising the drill to pass an obstruction.

When it is time to refill the seed hopper or take a break, the drill should be raised from the last
furrow, then wait for approx. 10 seconds. Switch off

auto advancing.

There is no need to switch

off

auto advancing

in case no additional lifting is required during the pause. When continuing

drilling, switch on

auto advancing

before the drill is raised the first time.

4.7

Bout markers

Setting of the bout markers using the Control Station is explained in

”3.30.2 Functions” on page

59.

Содержание Rapid RDA 400S











































































































































Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды

Vaderstad Rapid RDA 400S, Оригинальное руководство пользователя

Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды