Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 138

background image

Instructions and settings

42

27.06.2011

ver. 2

3.18 Scraper

Figure 3.42

The scraper default settings are shown in the figure.

The scraper position can be adjusted in two places. If the setting (A) is insufficient, the holder (B)
can be adjusted lengthwise.

NOTE!

The distance (C) between the scraper blade and the tyre must not be less than 5 mm. Rotate

the tyre by hand to verify that this distance is not less than 5 mm at any point.

!

Depending on the circumstances, a larger distance (C) may be required for optimum results. If
the scraper does not operate satisfactorily, then try with different scraper settings.

Example:

- If there are a lot of plant residues in the soil and it is humid, the scraper will usually provide
better results when the distance (C) is increased to approx. 20 mm.

- If the soil is humid without plant residues, the scraper will provide better results when mount-
ed in the default position (C = 5 mm).

B

A

C=5 mm

«
...
40
41
42
43
44
...
»

Содержание Rapid RDA 400S











































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid RDA 400S

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: GBC Страницы: 8

Бренд: KAPSCH Страницы: 57

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: Gainsborough Страницы: 2

Бренд: Bartscher Страницы: 28

Бренд: Bartscher Страницы: 13

Бренд: IBEX Страницы: 10

Бренд: M-system Страницы: 12

Бренд: HABYS Страницы: 16

Бренд: ParaBody Страницы: 3

Бренд: Valiani Страницы: 66

Бренд: Omlet Страницы: 60

Бренд: KCI Страницы: 2

Бренд: KCI Страницы: 60

Бренд: Landoll Страницы: 38

Бренд: Bartscher Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды