Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 15

Страница: 15 / 138

RDA 400S

27.06.2011
ver.2

1.6

Moving the machine when not hitched to a tractor

NOTE!

If the machine must be moved when not hitched to a tractor,it must be transported on a ma-

chine trailer or lorry flatbed!

The machine must be rolled onto and off the transport vehicle using a tractor. Lifting with a crane
is prohibited!

1 Set the machine to the transport position; see ”

3.7.2 Changing to transport position” on page

2 Activate the wheel retraction function (Only applies to machines with hydraulic depth setting),

see ”

3.6 Wheel retraction mechanism (only machines with the hydraulic depth adjustment

option)” on page 25

3 Raise the pre-implement to the full lifting height.

4 Reverse the machine lengthwise onto the trailer or flatbed. If using a flatbed, a ramp, loading

pier or similar will be required. Take great care. Check that no machine parts are damaged
during loading.

5 Lower the machine. Adjust the master cylinder's stop device and parking stay so that the

machine rests on the wheels, discs and support (or intermediate packer) in the lowered position.
Make sure that the machine's hydraulic system is depressurised.

6 Secure the machine's transport wheels to prevent rolling using chocks or similar.

7 Secure the tarpaulin using tension straps or similar.

8 Unhitch the tractor from the machine.

9 Secure the machine using suitable lashing equipment in accordance with applicable rules. The

lashing equipment must be attached to the machine at the locations indicated by the decals; see
“Figure 1.7”.

For information on the machine's dimensions and weight, see ”

7.4 Technical data” on page

135

Always make sure that you comply with applicable national regulations concerning transport
dimensions, requirements for escort vehicles or similar!

Figure 1.7

Содержание Rapid RDA 400S











































































































































Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды

Vaderstad Rapid RDA 400S, Оригинальное руководство пользователя

Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды