Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 138

background image

RDA 400S

27.06.2011
ver.2

67

3.31 Interactive Depth Control function, IDC (option

15582-)

!

In order to use the Interactive Depth Control function, the Control Station must be loaded with
firmware version 210004 or later.

If “Yes” is selected in the programming menu

, see ”

3.30.3 Programming” on page 63

, the

menu is accessed via the “Low-lift/Drilling depth” menu. For detailed information, see below. The
low-lift switch is now replaced by an analogue sensor.

To gain access to the setting and calibration menus without having to restart the Control Station,

keep the

button depressed while simultaneously depressing

.

3.31.1

Low-lift/Drilling depth" setting menu

Figure 3.71

NOTE!

If calibration must performed first, select “Calibrate” and depress

. The calibration

menu is explained in ”

3.31.2 Calibration menu” on page 68

. New drills have already been cali-

brated upon delivery from the factory.

1 Set the desired low-lift scale value here. The height above ground is displayed as a negative

value. The basic setting is -10, which corresponds to a low-lift height of 10 cm above ground.
Also see ”

3.15 Adjusting Low lift height” on page 39

2 The current scale value of the lifting ram is displayed here.

3 Set the desired drilling depth scale value here. The drilling depth is displayed as a positive val-

ue. The drilling depth value should exceed the low-lift level. The drilling depth value is not an
exact depth in centimetres but rather serves as a reference.

4 Use this to set when seed output should stop when the drill is raised from the furrow. The value

set here corresponds to how much the drill is raised from the set drilling depth before seed out-
put is switched off. The default setting is -4.0. This means that seed output from the drill is
switched off when the machine is raised 4 cm from the set drilling depth.

5 Select “Calibrate” here and then depress

to gain access to the calibration menu. See

3.31.2 Calibration menu” on page 68

To return to the programming menu, select OK and depress

or cancel by depressing

1

2

3

4

5

«
...
65
66
67
68
69
...
»

Содержание Rapid RDA 400S











































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid RDA 400S

Бренд: Makerfire Страницы: 10

Бренд: YSI Страницы: 70

Бренд: jcb Страницы: 41

Бренд: Raytech Страницы: 21

Бренд: Teac Страницы: 2

Бренд: laerdal Страницы: 2

Бренд: Danelec Страницы: 67

Бренд: Echo Страницы: 6

Pro Attachment Series

Бренд: Echo Страницы: 28

Бренд: Echo Страницы: 2

Pro Vantage 12+ Series

Бренд: Ecco Страницы: 6

Tablet1000 Series

Бренд: Hantek Страницы: 98

Бренд: P-Q Controls Страницы: 5

Бренд: P+L Systems Страницы: 2

Бренд: Tascam Страницы: 78

MINISTUDIO CREATOR US-42

Бренд: Tascam Страницы: 11

LED Street Bar 16x3W RGB IP65

Бренд: Varytec Страницы: 9

Бренд: VARILITE Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды