Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 27

Страница: 27 / 138

RDA 400S

27.06.2011
ver.2

Keep the hydraulic lever on the tractor in the lowering position (

Note!

"Floating" position

must not be used) until the ram ("folding ram") is fully refilled, locking the wing sections in
the unfolded position. See “Figure 3.19”.

Figure 3.21

Always drive forwards when the seed drill is lowered to its working position, to prevent the
seed coulters becoming clogged.

Lower the tool bar to its working position.

Undo the safety cotter pins of the bout markers.

3.7.2

Changing to transport position

Switch off the low-lift function at the control box. Raise the seed drill to its top position.

Note!

When the wing sections are being folded and unfolded, the mid section must always be in its
fully raised position.

Fold the drill.

Check whether the automatic locking devices engage.

Check that front implements and trailing implements do not exceed the 3 metre transportation
width limit.

Block the bout markers with the safety cotter pins.

Figure 3.19

Figure 3.20

Содержание Rapid RDA 400S











































































































































Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды

Vaderstad Rapid RDA 400S, Оригинальное руководство пользователя

Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды