Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 138

background image

Instructions and settings

74

27.06.2011

ver. 2

3.32.3

Adjusting track width

Figure 3.80

The Rapid drill is usually supplied with the row shutoff and track width specified by the customer.
However, it is possible to change these if necessary:

!

A different track width can be obtained by shifting the feed hoses to the seed coulters.

Example:

A track width of 1.75 m can be increased to 2.0 m by moving the front left and rear

right one step outwards. A track width of 1.5 can be produced by moving the rear left and the fore
right one step inward (Y). For bigger changes in track width, it may be necessary to move the hos-
es inside the hopper instead.

3.32.4

Adjusting row shutoff

Figure 3.81

Tramlining can be done with 1, 2 or 3 row shutoff.

!

The sowing row shutoff can be altered by exchanging the spring under the distributor head for
an operating spring (417772, 417776) or a parking spring (417795) depending on whether
more or less rows are to be shut off.

Table 3.6 Possible track widths

One row shutoff

Two row shutoff

Three row shut-off

C-C 138 cm

C-C 150 cm

-

C-C 163 cm

C-C 175 cm

C-C 163 cm

C-C 188 cm

C-C 200 cm

C-C 188 cm

C-C 213 cm

C-C 225 cm

C-C 213 cm

C-C 238 cm

C-C 250 cm

-

417766, 400 S

417795

«
...
72
73
74
75
76
...
»

Содержание Rapid RDA 400S











































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid RDA 400S

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

Бренд: GALLERY Страницы: 18

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: Kapriol Страницы: 32

Бренд: JABO Страницы: 4

Бренд: Latchways Страницы: 80

Бренд: Kapriol Страницы: 28

Бренд: Parr Instrument Страницы: 24

Бренд: JBL Страницы: 15

Бренд: ParaBody Страницы: 6

Бренд: Sailmon Страницы: 10

Бренд: B&W Tek Страницы: 12

Бренд: b&o Страницы: 46

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды