Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 138

background image

Maintenance and service

92

27.06.2011

ver. 2

5.1

General maintenance

Figure 5.5

A machine is only as good as the service it receives!

Before starting work, check that all nuts and screws are tightened. During the season, check the
tightness of nuts and screws regularly, as well as the wear on linkages and the hydraulic ram
mountings.

NOTE!

The screws holding links should not be tightened so much that movement in the linkage is

restricted.

NOTE!

When cleaning the drilling system or when servicing the transmission system on machines

with hydraulic feed output, the hydraulic flow to the fan and feed output driving mechanism must
always be shut off beforehand.

The hydraulic system does not normally require any maintenance, but check that the hoses and
couplings are undamaged.

NOTE!

Dirt must be kept out of the hydraulic system during any service work. Wipe with clean

paper or a clean rag. Lay the parts on a clean surface (not directly on the work bench). Rinse off
parts with e.g. a degreasing compound before fitting them.

Always grease the piston rods after cleaning them or if the drill is not going to be used for a long
time.

Grease galvanized and chromium plated surfaces before long periods of storage.

To maintain the quality of this seed drill, always use Väderstad original spare

parts.

«
...
90
91
92
93
94
...
»

Содержание Rapid RDA 400S











































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid RDA 400S

Бренд: Rangevision Страницы: 31

Бренд: Panasonic Страницы: 9

BTL PA0400 Series

Бренд: Balluff Страницы: 22

Micropulse BTL5 Series

Бренд: Balluff Страницы: 12

BNI IOW-560-W01-K022

Бренд: Balluff Страницы: 32

Бренд: Baltic Страницы: 68

Бренд: Baltic Страницы: 68

Max Charge MC-612

Бренд: Balmar Страницы: 12

BTL PA0400 Series

Бренд: Balluff Страницы: 204

Бренд: Federal Страницы: 43

Бренд: Mainca Страницы: 21

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: Rane Страницы: 6

Бренд: Rane Страницы: 27

Бренд: Ranger Products Страницы: 6

Бренд: Rane Страницы: 88

Бренд: Haag-Streit Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды