Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 135

Страница: 135 / 138

RDA 400S

27.06.2011
ver.2

135

7.4

Technical data

NOTE!

All height measures can be reduced by approx. 200 mm if the machine has not been raised

to its highest top position.

Fan

Noise level: 92 dB(A) (EN-1553)

Tyre inflation pressures

740x180-15”: 2.5 kg/cm

(250 kPa)

200x14.5”: 4.1 kg/cm

(410 kPa)

Table 7.17

Machine

RDA 400 S

Working width (m)

4,0

Transport width (m)

3,0

Transport height (m)

3,1

Transport height with hopper extension (m)

3,5

Filling height (m)

2,6

Filling height with hopper extension (m)

3,0

Hopper capacity (litres)

3000

Seed hopper volume with hopper extension (litres)

3750

Max. load in hopper (kg)

3000

Max. trailed weight on tractor (kg)

2200

Disc weight, each approx. (kg)

127

Machine weight:
Crossboard (kg)

4350

System Agrilla (kg)

5050

System Disc (kg)

5450

Weight accessory:
Centre packers (kg)

300

Top grating (kg)

Pre-emergence markers (kg)

Wing packers (kg)

2x170

Power requirement, approx. (kW)

90-120

Содержание Rapid RDA 400S











































































































































Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды

Vaderstad Rapid RDA 400S, Оригинальное руководство пользователя

Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды