UTICA BOILERS MACF-115 Скачать руководство пользователя

Страница: 130 / 139

Domestic hot water

Turn on mains power.

The display illuminates

09,

15 and

384 is flashing or re-occurs regularly

check all PCB connections, if this has no effect replace

the PCB.

YES

Error 110 or 133 or 134

or 135 or 125 or 384 or

09 or 15 flashing

YES

Go to section 'A'

Press the 'Reset' button for

between 1-3 seconds

Go to section 'D',

If the E11 o is still flashing. Go

to section 'H'

Error 20, 28, 40, 50, 321 or 431 flashing

if E55 is displayed go to section N

YES

Error 117 or 118 flashing

Go to section 'I'

DH\V Top. Symbol nashcs

�---'-------,,/c,

Open DHW tap fully.

Pump runs.

YES

Fan runs after up to 3 seconds

YES

Fan runs at correct speed

YES

Spark at ignition electrodes for

up to 5 seconds and for 5

attempts.

YES

Burner lights

YES

Error E109 flashing

Error E110 flashing

YES

DHW flow rate more

than 21/min

Error 160 flashing

Go to section 'C'

Error 160 flashing

Go to section 'C'

Error 133 flashing

Go to section 'E'

Burner does not stay alight

after 5 seconds

Error E125 flashing

after 1 minute

Go to section 'H'

Go to section 'L'

If E53 is displayed go to section 0

YES

1------�

Go to section 'F'

YES

Error 128 or E129 flashing (loss of flame 12

times) Go to section 'G'

Go to section 'J'

3 way valve open to domestic

hot water circuit

1----1�

.. �o to section 'K'

�-----------�

Burner output modulates to

maintain the temperature set

YES

Error E130 flashing

YES

Burner goes out

Check the Central Heating NTC sensor

Go to section 'D'

Go to section 'M'

Fan stops after 30 seconds

YES

Operation sequence

successful

TROUBLESHOOTING CHART

PN 240012875 REV. C [10/01/2021]

Содержание MACF-115












































































































































Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды

UTICA BOILERS MACF-115, Руководство пользователя

Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды