UTICA BOILERS MACF-115 Скачать руководство пользователя

Страница: 137 / 139

Commissioning

Function

is as follows

•

When power is supplied to the boiler for the first time

will

be displayed. If

is shown, press

, for at least 2 seconds

will now be displayed.

•

Press

together and hold for at least 6 seconds.

The “

De-Aeration

” Function will be activated & “

” showing.

•

The boiler pump will run for up to 10 minutes. For 3-way valve

models the valve will switch between heating & hot water. This
will purge air from the system. The display will show

Gas Type Check

•

Once de-aeration is complete on first fire-up the boiler will light

and operates for 6 or 7 minutes to automatically check the

gas type Gas A (Natural Gas “

”) or Gas E (Liquefied

Petroleum Gas “

LPG

”). The boiler software check the

combustion value against the set value.

will be displayed

alternating the

value

of ignition power

and the temperature value °F(°C).

•

On a Gas A (Natural Gas) supply the display shows

for at

least 10 seconds and the boiler is ready for the normal

operation. If the display shows , press

together

and hold for at least 4 seconds to exit the function without

saving.

•

On a Gas E (LPG) supply the display show

, press

for

at least 6 seconds to confirm that this is the intended gas type

for the installation

If the display shows , press

together and hold for

at least 4 seconds to exit the function without saving then

modify

P02=01

as described in the Manual Instructions for the

Installer section “PARAMETERS SETTING”.

•

While the gas type is being identified, the boiler may be noisy.

IF THE BOILER IS TO BE OPERATED ON GAS E (LP) REPLACE THE

EXISTING LABEL WITH THE GAS E LABEL SUPPLIED WITH

IS INSTRUCTION

ASSURE FACTORY SUPPLIED CONVERSION

LABEL IS APPLIED TO PRODUCT IF CONVERTING TO LP.

IMPORTANT: Gas type Check

Ensure

the maximum heat exchange to the system

in Heating or DHW mode (DHW request) in order to

avoid the boiler shutoff for overheating.

FUNCTION INTERRUPT

If either De-aeration or Gas Check is interrupted by electrical

power failure is necessary to reactivate the function by
pressing

together for at least 6 seconds.

During De-aeration, if the display shows E118 (water low

pressure), open the water filling tap and repressurising the

system to the correct pressure value.

During Gas Type Check, if the display shows E133 (Ignition
Failure), press

button to Reset then press together

for at least 6 seconds to restart the function.

During Gas Type Check, if the boiler switch off for

overheating failure is necessary to reactivate the function by
pressing

together for at least 6 seconds.

IMPORTANT

: The combustion for this appliance has been

checked, adjusted and pre-set at the factory for operation on

the gas type specified on the appliance data plate.

During the Gas Type Check Function the combustion

ratio will increase for a short time while the gas type is

established.

The display shows the Gas Type Check

IMPORTANT INFORMATION

READ THIS LEAFLET BEFORE COMMISSIONING THE BOILER

IMPORTANT:

Upon

startup

of this

new

boiler

please call

ECR International, Inc. Technical Support

for

installation assistance and registration

Technical Support

and Product Registration

Monday

Friday

8AM to 6PM Eastern time.

1.800.253.7900

Described below is the procedure to activate the

Commissioning Function wi

hich

includes

De-Aeratio

Function/Gas

Type Check when power is first supplied to the boiler and the actions required when on a Gas E (LPG) supply.

240011376 REV

, [0

/20

]

Содержание MACF-115












































































































































Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды

UTICA BOILERS MACF-115, Руководство пользователя

Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды