UTICA BOILERS MACF-115 Скачать руководство пользователя

Страница: 56 / 139

9.15 Parameter Settings

Program boiler electronic board parameters as follows:

• Press

and

together, hold them down

for 6 seconds until program “

P01

” appears on the

display alternated with the set value;

• Press

to scroll the list of parameters;

• Press

, value of selected parameter begins

flashing, press

to change the value;

• Press

to confirm the value or press

exit without saving.

Further information in regards to parameters listed in

the following table are supplied together with required

accessories if necessary.

Parameters continued on next page

For Natural Gas :

Input (MBH)

3600 x cu ft
seconds

Example: Natural Gas - Gas flow from

Meter = 2 cu ft
Measured time = 72 seconds

3600 x 2 cu ft

= 100 MBH

72 seconds

For Propane (LP):

Input (MBH)

9160 x cu ft
seconds

For Metric formulas- See Glossary

Compare measured input to table below. If

calculated input is not in range given in Table 9-2

check firing rate again after setting the combustion

following steps in section 9.12.

Input Rate (MBH)

9 - START UP PROCEDURE

Approximate Rate @

100% Fire (MBH)

Size

100

93.5

115

125

150

165

164

205

9.16 Description Of Parameters: Factory Settings

FACTORY

SETTINGS

100,

125,165

115,

150,205

P01

Manufacturer information

P02

Gas used
00

= Gas A (Natural Gas)

= Gas E (LPG Gas)

P03

Hydraulic system

= instantaneous appliance

= instantaneous appliance with pre-heat function

= heating only appliance with DHW thermostat

= appliance with external storage indirect tank

= heating only appliance

= instantaneous appliance with pre-heat function for solar application

P06

Outdoor temperature sensor input configuration

= with outdoor temperature sensor connected, external temperature value has influence to calculate

heating flow temperature set-point

= with outdoor temperature sensor connected, display shows external temperature value (no

influence)

02…05

= no function is associated

P07

00..02

= No function is associated

= This is an input contact for CH request (e.g. trigger phone).

When contact CN2 is closed and Room Thermostat (RT) requiring heat switches burner on.

Note:

verify heating mode is enabled (winter or heat only mode)

= This is an input contact for Low Temperature Thermostat (e.g. floor heating system).

When Low Temperature Thermostat connected on CN2 cuts out, burner switches off and display

shows

E178

anomaly.

Note:

verify heating mode is enabled (winter or heat only mode)

= This is an input contact for external DHW recirculation pump. When contact CN2 is closed the

pump runs for a specific period.

To enable input it is necessary to set parameter

P04 or P05 = 08

and

P69 = 05

Pump will run at

P19

minutes (Summer/Winter mode or Only Winter mode) or

P19/2

minutes

(only Summer mode).

P09

Manufacturer information

Default 01

NOTICE

Important!

Record any changes made to

Parameters on chart found on Page 46 of the

Application Guide supplied with your boiler.

Table 9-2 Input Rate @ High Fire (MBH)

240013371 REV B, [10/01/2021]

Содержание MACF-115












































































































































Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды

UTICA BOILERS MACF-115, Руководство пользователя

Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды