UTICA BOILERS MACF-115 Скачать руководство пользователя

Страница: 23 / 139

5.4 Approved Venting Materials

5.5 Vent Termination

•

Terminate combustion air and vent pipes with fittings

or coaxial vent kit. Use horizontal pipe for vent and

90° elbow for combustion air termination when using

fittings.

• Separate vent terminal from air inlet terminal to

prevent flue gas recirculation. If T-Terminal is used

on flue pipe at sidewall, air inlet terminal shall be at

least 36" or more away from vent terminal.

• Locate combustion air termination as far as possible

from swimming pool, swimming pool pump house,

and other sources of airborne chlorine.

• Locate combustion air and vent terminals as required

by authority having jurisdiction.

Approved Polypropylene Manufacturers

* Natalini
* DuraVent

*Centrotherm
* Z-Flex

Note: Maximum equivalent length may vary between

manufacturers.

Installation shall conform to requirements of authority

having jurisdiction or in absence of such requirements:

• USA - National Fuel Gas Code, ANSI Z223.1/NFPA

54.

WARNING

Manufacturer recommends this condensing boiler

be vented with approved polypropylene venting

material. Use only materials listed below for

vent pipe, intake air pipe, and fittings. Failure to

comply could result in death or serious injury.

WARNING

Do not use cellular core pipe. Only specified

sized pipes are to be used. When using venting

material other than boiler manufacturer's

venting, note the correct installation procedure.

Failure to follow these instructions could result in

death, or serious injury.

WARNING

•

Covering non-metallic vent pipe and fittings

with thermal insulation shall be prohibited.

•

Use of cellular core PVC for venting flue gas

could result in death, or serious injury.

• Coaxial venting shall be fastened with screws.

Dual flue venting is NOT fastened with screws.

Venting shall be properly supported.

Boiler shall not support any type of vent system.

All piping, glue, solvents, cleaners, fittings and

components must conform to ASTM and ANSI

standards. In Canada ULC S636 and in the USA UL

1738 schedule 40 CPVC are the only approved vent

system to be used as an alternative to polypropylene

venting for the exhaust pipe.

Manufacturer requires use of a mechanical fastener

at every push-fit gasket connection when using a

single wall polypropylene vent system.

5 - COMBUSTION AIR AND VENT PIPING

WARNING

Pipe outdoor combustion air directly to boiler

air connection. Ensure combustion air does not

contain contaminants and is not drawn from an

area likely to have contaminants per Table 5-2.

For example, never pipe combustion air from

areas near swimming pools or laundry room

exhaust vents. Contaminated combustion air

will damage boiler resulting in death or serious

injury.

Install an air filter which allows at least 800 cfm if

the area is subject to dirty or dusty intake air. Boiler

performance at maximum length may be impacted when

an air filter is used.

If interior or exterior construction in vicinity of boiler

is taking place, take precautions to avoid exposing the

boiler to fine particulate dust. If boiler is exposed to

any dust or dirt it must be cleaned and serviced.

240013371 REV B, [10/01/2021]

Содержание MACF-115












































































































































Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды

UTICA BOILERS MACF-115, Руководство пользователя

Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды