UTICA BOILERS MACF-115 Скачать руководство пользователя

Страница: 61 / 139

11.1 Beginning of Each Heating Season

• Check boiler area is free from combustible materials,

gasoline, and other flammable vapors and corrosive

liquids.

• Visually inspect combustion air and vent piping

for proper operation. Check for and remove any

obstruction to flow of combustion air or vent

gases. Immediately repair or replace pipe showing

deterioration or leakage. Reassemble per instructions

in section 5. Ensure proper reassembly and resealing

of system.

• Visually inspect condensate drain line for proper

operation. Checking for deteriorated or plugged

condensate drain line. Verify condensate trap drains

freely and clean as required.

• Test safety relief valve for proper operation. Refer to

valve manufacturer's instructions packaged with relief

valve.

• Examine heat exchanger, burner, condensate lines, and

clean (if necessary) by following instructions in section

11.3 - Component Replacement And Cleaning.

CAUTION

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation.

DANGER

Before servicing, turn off electrical power to

boiler at service switch. Close manual gas valve

to turn gas supply OFF to boiler. Failure to

comply will result in death or serious injury.

Note

erify proper operation after servicing.

Note

Perform regular service and maintenance

by qualified service agency at least once

every 12 months to assure safe, trouble

free operation and maximum efficiency.

• Circulator pump and combustion air blower motor

furnished with boiler are permanently lubricated from

factory and require no further lubrication. Lubricate

field sourced pumps and/or motors according to

pump and/or motor manufacturer’s instruction.

• Check following components are operating properly

and are free of blockages or obstructions:

• air vent;
• check venturi air inlet for blockage and clean as

required;

• verify pressure test port cap and combustion test

port caps are in place;

• verify supply and return sensors are properly

clipped to pipes as close to heat exchanger as

possible;

• Check boiler for any sign of leaks.

•

Check external low water cutoff operation (if

installed).

• Check operation by pressing test button on low

water cutoff.

• "Low Water" LED on the external LWCO should

illuminate and boiler should shut down.

•

Every 5 years remove low water cutoff. Reinstall

after cleaning.

•

Every 10 years replace low water cutoff.

•

Visual inspection of flame through sight glass. Burner

should be fully illuminated.

• Check heating system expansion tank.

Note

A Heat Exchanger cleaning kit is available
for annual service of the boiler. See repair
parts manual for part number.

11 - GENERAL MAINTENANCE AND CLEANING

240013371 REV B, [10/01/2021]

Содержание MACF-115












































































































































Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды

UTICA BOILERS MACF-115, Руководство пользователя

Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды