UTICA BOILERS MACF-115 Скачать руководство пользователя страница 53

Страница: 53 / 139

9.7 Commissioning For The First Time:

Turn power to boiler on. Code

"000"

appears on the

display. Appliance is ready for "commissioning" procedure.

Press

at the same time. Hold for 6 seconds. "

appears on the display for 2 seconds followed by code

312

" indicating "

de-aeration

" function is active. This

function lasts 10 minutes.

Boiler will turn on after deaeration function is complete.

Display will show code "

000

" alternating with

ignition power and temperature value (°F / °C).

• During this

gas recognition function

phase which lasts

about 7 minutes, type of gas being used is analyzed.

• During this function, ensure maximum heat exchange

out to the system with all zones and circulators running.

Maintain system temperature below 176° F for duration of

the process until

LPG

are seen on the display.

• If boiler operates on Gas A (Natural Gas) and display

shows

LPG

(Gas E), press

and

together

and hold down for at least 4 seconds to exit without

changing factory setting. Boiler will stay set to Natural

Gas.

• If boiler operates on Gas A (Natural Gas), display shows

(Natural Gas) for about 10 seconds. Boiler is now

ready for normal operation.

• If boiler operates with

Gas A

(Natural Gas) and the

display shows LPG (Gas E), press

and

together

and hold down for at least 4 seconds to exit the function.

Change parameter

P02=01

as described in section 9.15

Parameter

Settings

of boiler Installation, Operation and

Maintenance Manual. Perform Automatic Calibration

Function. Manual Calibration may be necessary if

combustion is not within specified range.

• If boiler operates on Gas E (LPG) and display shows LPG,

press for at least 6 seconds to confirm gas used.

•

After fuel type is detected confirm

P02

is set for the

desired fuel type by checking parameter see section 9.15.

NOTICE

First ignitions immediately after installation,

system will implement a self-learning procedure

to reach correct ignition level.

9 - START UP PROCEDURE

9.8 Automatic Calibration Function

Before performing this function verify the door is on the

boiler and there are no heat demands in progress.
During this function ensure there is maximum heat

exchange to the system in Heating or DHW mode (DHW

request) to avoid boiler shutting off due to overheating.

Press

and

together and hold for about 6

seconds. When display indicates "

" press

within

3 seconds after pressing previous buttons.

NOTICE

IMPORTANT:

If Calibration function does not

complete, verify unit did not shut down for over-

temperature. Repeat Automatic Calibration.

Replace KEY if Automatic Calibration does not

complete after second try.

NOTICE

Important:

If display indicates "

303

" Automatic

Calibration function has not been activated.

Disconnect boiler from main power supply for few

seconds and repeat procedure.

When function is enabled, and

will flash on

the display.

After ignition sequence, which can also take place

after few attempts, boiler performs three operations.

Each operation lasts about 1 minute:

• maximum power

• ignition power
• minimum power

Before moving to the next combustion point the

and appear on the display as the control is setting

values.

During this phase, power level reached by boiler and

delivery temperature alternate on the display.

When , and

flash together on the display,

automatic calibration function has completed.

Press

to exit the function. Display will show

ESC

Verify combustion is within specified range. If not,

perform Automatic and then Manual Calibration.

(See Sections 9.8 & 9.9)

Note

Boiler must not shutoff during calibration.

Open all heating zones in heating or DHW

mode to ensure boiler does not shutoff.

NOTICE

All connections shall be made and water added

before performing this function.

9.6 Prior to Commissioning:

• Verify door is ON boiler;

• Check system pressure is correct;

• Power boiler;

• Open gas tap (positioned under boiler);

• Select required heating mode. See section 10.4

Operating Modes.

WARNING

Asphyxiation hazard! Fill condensate trap before

starting boiler to avoid combustion products escaping

boiler. Failure to follow these instructions could result

in death or serious injury.

240013371 REV B, [10/01/2021]

Содержание MACF-115












































































































































Результаты поиска

Содержание MACF-115

Отзывы:

Бренды по названию

Популярные бренды

UTICA BOILERS MACF-115, Руководство пользователя

Результаты поиска

Содержание MACF-115

Отзывы:

Бренды по названию

Популярные бренды