UTICA BOILERS MACF-115 Скачать руководство пользователя

Страница: 27 / 139

5 - COMBUSTION AIR AND VENT PIPING

5.8 Twin Pipe Systems

Twin pipe venting allows exhaust flue and intake flue to

be separated from each other. Fresh air is drawn in at a

different area from the flue terminal location.

Twin Pipe CPVC System

CPVC is approved for boiler exhaust. CPVC or PVC are

both approved for air intake.

To transition from Coaxial at the top of the boiler to Twin

Pipe CPVC/PVC a kit is available.

Twin Pipe Polypropylene System

Single wall polypropylene is used for both exhaust and

air intake piping. PVC can be used on

intake only

twin pipe applications.
Use the appropriate transition kit to change from

polypropylene to PVC. To transition from Coaxial, at the

top of the boiler to Twin Pipe polypropylene venting an

adapter kit is available.

Twin Pipe Separated Flue

Exhaust and combustion air intake are not located in

same general location.

Twin Pipe - Common Atmospheric Zone

Termination

Exhaust and combustion air intake are located in same

general location and are of equal length.

Grade, Snow

& Ice

Maintain 12"(305 mm) US, 18"(457

mm) Canada clearance above highest

anticipated snow level, 24" (610 mm)

above roof.
Avoid locations where snow may drift
and block vent and combustion air.
Ice or snow may cause boiler to shut
down if vent or combustion air becomes
obstructed.

WARNING

Asphyxiation hazard! Improper installation could

result in death or serious injury. Read Twin

Pipe Installation Instructions completely and

understand all requirements before beginning

installation.

FIGURE 5-8 - 2"/60 mm & 3"/80 mm Twin Pipe

Separated Horizontal Flue Termination

This Termination

can be used on:

2" / 60 mm ON

165/205

3" / 80 mm

ON ALL SIZES

vent only

FIGURE 5-9 - 2"/60 mm & 3"/80 mm Twin Pipe

Separated Horizontal Flue Termination

This Termination

can be used on:

2" / 60 mm ON

165/205

3" / 80 mm

ON ALL SIZES

vent only

FIGURE 5-10 - 2"/60 mm & 3"/80 mm Twin Pipe

Separated Horizontal Flue Termination With Tee On

Exhaust - CAN BE USED ON ALL SIZES

This Termination

can be used on:

2" / 60 mm

ON ALL SIZES

3" / 80 mm

ON ALL SIZES

vent only

Twin Pipe Maximum Vent Lengths

(Includes first elbow and termination)

Boiler

100/115/125/150

165/205

All

Vent Size

[80 mm]

[60 mm]

[80 mm]

[60 mm]

All

Maximum

Minimum

Intake
Vent

49 ft

[15m]

85 ft

[25.9m]

100 ft

[30.5m]

85 ft

[25.9m]

6 ft

[1.8 m]

Exhaust
Vent

147 ft

[45m]

Combined
Vent

L1+L2

196 ft

[60m]

170 ft

[51.8m]

200 ft

[60.9m]

170 ft

[51.8m]

12 ft.

[3.6 m]

Single Wall Elbows - Equivalent Length

3" (80 mm)

2" (60 mm)

45° bend

0.82 ft [0.25 m]

3 ft [0.91 m]

90° bend

1.64 ft [0.50 m]

5 ft [1.5 m]

NOTE: Two pipe can be installed horizontally or vertically.

240013371 REV B, [10/01/2021]

Содержание MACF-115












































































































































Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды

UTICA BOILERS MACF-115, Руководство пользователя

Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды