UTICA BOILERS MACF-115 Скачать руководство пользователя

Страница: 54 / 139

NOTICE

During initial ignition, burner may not ignite. This

may cause boiler to shut down until any air in gas

pipes is vented. Repeat ignition procedure until

gas reaches the burner. To reset boiler operation,

press

for at least 2 seconds.

9.10 De-Aeration Function

Used to eliminate air inside the heating circuit when

boiler is installed or after maintenance when water is

drained from primary circuit.

Press buttons

together and hold for 6

seconds.

appears on display for a few seconds,

followed by program row

312

The electronic board will activate pump on/off cycle

for 10 minutes. Function will automatically stop at

end of cycle.

To manually exit this function, press

buttons together and hold for 6 seconds.

9.11 Commission Set Up (Gas) - Changing The Type

Of Gas

During the

first

installation boiler carries out an

automatic commissioning function.
The system is able to detect the gas type present in the

network.

Correct gas type setting, is made by pressing two buttons at

the same time, see section 9.6 Commissioning.

Change of gas type is made

after

the first installation:

• Change parameter P02. See section 9.6

Commissioning

and

section 9.15

Parameter

Settings.

• Check minimum gas pressure is suitable for selected gas:

Minimum gas pressure is determined with boiler operating

at high fire and any other appliances connected to same fuel

source operational as well (whole house load)

Gas A (NG) = 3.5" (8.7 mbar)
Gas E (LPG) = 8.0" (19.9 mbar)

• Place supplied label with indication of gas type close

to the data plate of boiler replacing the original.

• Perform Automatic Calibration Function -

Section 9.8.

• Manufacturer recommends

verification of CO

concentration on the flue.

FIGURE 9-3 - Gas Inlet Tap - Pi

9 - START UP PROCEDURE

PI = Gas Supply Inlet Pressure Tap

IMPORTANT INFORMATION

A. If gas recognition function is interrupted by power

blackout, start function again when power is

restored. Press

and

together and hold at

same time for at least 6 seconds.

B. If display shows fault

E118

(low pressure in

hydraulic circuit) open filling tap on appliance and

restore correct pressure.

C. If gas recognition function is interrupted due

to fault (e.g.:

E133

no gas) press

reset. Then press

and

(for at least

6 seconds) to restart the function again.

If gas recognition function is interrupted due to

overheating, restart function by pressing and

holding down together for at least 6 seconds.

D. Combustion of this appliance has been factory

controlled, calibrated and set for operation with

Gas A

(Natural Gas).

E. During Gas Type Control Function, combustion ratio

will increase for a short period of time while gas

type is being established.

9.9 Manual Calibration Function:

Manual Calibration phase starts at the end of the

Automatic Calibration.
The Display shows the boiler power and adjustment

of the CO2 value (parameter setting) during Manual

Calibration sequence.
The process begins at minimum power.

A. After Automatic Calibration sequence with

flashing together on the display, you can adjust

minimum power combustion by pressing

lower % CO

, and

to raise % CO

B. When minimum power combustion is in the

specified range, press

and then

to reach

ignition power.

C. Press

to adjust ignition power combustion.

Press

to lower % CO

, and

to raise % CO

When ignition power combustion is in the specified

range, press

and then

to reach maximum

power.

E. Press

to adjust maximum power combustion.

Press

to lower % CO

, and

to raise % CO

F. When maximum power combustion is in the

specified range,

press

to exit Manual Calibration

Function.

ESC

is displayed on the screen.

240013371 REV B, [10/01/2021]

Содержание MACF-115












































































































































Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды

UTICA BOILERS MACF-115, Руководство пользователя

Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды