UTICA BOILERS MACF-115 Скачать руководство пользователя

Страница: 48 / 139

8.8 Indirect Storage Tank

Heating system

Three way diverter valve

Heating water flow

Heating supply to DHW indirect storage tank

coil

Heating water return

Tank

Optional 10k Ω DHW priority sensor

Boilers MAHF- 100, 125 & 165 can be electrically

connected to indirect storage tank as follows:

• Connect DHW priority

10K

sensor NTC to

terminals

3-4

on terminal block

• Insert

10K

NTC sensor element in the sensor

well of indirect storage tank.

• Verify exchange capacity of the storage boiler coil is

appropriate for boiler power.

• Adjust DHW tempe95 °F...+140 °F (+35

°C...+60 °C) by pressing

on boiler

Control.

IMPORTANT: set parameter P03 = 05 as described in:

"PARAMETER SETTINGS".

*125 Model shown - See Application Guide for sizes 100 & 165

Note

Sensors used for this boiler are proprietary
to the manufacturer. Use of after market
sensors will diminish boiler performance.

8 - ELECTRICAL CONNECTIONS

FIGURE 8-7 Kt Indirect Storage Tank

8.9 Management of 0-10V Input

The functions with 0...10V regulator are activated by means of their parameters:
To enable 0-10V input change

P82=4

P82=3

When

P78=1

the input manages the

heating set point temperature directly.

When

P78=2

the input manages the

heating power input directly

Demand is activated above 3V and heating setpoint is calculated in proportion to deviation from 3 to 10 V DC, to

give a setpoint that goes from minimum to maximum.
Terminal # 9 is negative (-), terminal #10 is positive (+).

* See "Application Guide" for details on using a DHW

tank aquastat.

P78=1

P78 = 2

Voltage

Temp Setting

100/115

125/150

165/205

°C

°F

MBH

0-3

OFF

4.9

16.6

6.4

22.0

8.6

29.5

8.4

28.9

10.7

36.5

14.4

49.0

104

12.0

40.8

14.9

51.0

19.9

68.0

120

15.4

52.4

19.2

65.5

25.5

87.0

135

18.5

63.1

23.4

80.0

31.1

106.0

149

22.2

75.7

27.7

94.5

36.6

125.0

163

25.3

86.2

31.9

109.0

42.5

145.0

176

27.4

93.6

36.9

125.0

48.1

164.0

240013371 REV B, [10/01/2021]

Содержание MACF-115












































































































































Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды

UTICA BOILERS MACF-115, Руководство пользователя

Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды