UTICA BOILERS MACF-115 Скачать руководство пользователя

Страница: 19 / 139

4.1 Boiler Location Considerations

• Ambient room temperature always above 32°F

(0°C) to prevent freezing of liquid condensate.

• Approved for installation in closets or alcove

provided it is correctly designed for that purpose

and minimum clearances are met.

• Protect gas ignition system components from

water (dripping, spraying, rain, etc.) during

operation and service (circulator replacement,

condensate trap, control replacement, etc.).

• Access to outdoors to meet minimum and

maximum pipe lengths for combustion air and

vent piping. See section 5.

• Disposal of condensate. See section 5.
• Drainage of water (or water - antifreeze solution)

during boiler service or from safety relief valve

discharge. See section 6.

• Access to system water piping, gas supply, and

electrical service. See sections 6, 7 and 8.

• Clearances to combustible materials and service

clearances. See Table 1 and Figures pg. 16.

• Room-sealed boiler installed in a room containing

bath or shower shall be installed so person using

bath or shower cannot touch any electrical switch

or boiler control utilizing line voltage electricity.

• Multiple Boilers can be placed side by side, or

back to back.

• Observe service clearances in all installations.
• For Direct Vent installations, air vents are not

required in room boiler is installed in, or when

installed in closet or compartment.

• Requires fresh air intake piped from outdoors.
•

Install a filter on the air intake if boiler is installed

in dusty or dirty environment. A high flow air

filter with minimum air filtration of 800 cfm can

be placed on the air intake section of the vent

pipe. Boiler performance at maximum vent length

may be impacted when an air filter is used.

• Use of unregulated gas (well gas) is not

manufacturer recommended with this boiler.

WARNING

Fire Hazard! Do not install on carpeting. Failure

to follow these instructions could result in death

or serious injury.

4 - LOCATING BOILER

4.2 Floor Location

• Place crated boiler as close to selected location as

possible and uncrate boiler. Boiler may be moved

into position with appliance dolly or (2) two wheel

hand truck. Insert dolly or hand truck under left

hand side of boiler. It is possible to slide boiler for

short distance on smooth floor or surface.

• Adjust the position of the boiler verify it is level

and plumb.

• Select level location central to piping systems

served and as close to vent and air intake

terminals as possible.

• Accessibility clearances, if more stringent (i.e.

larger clearances) than required fire protection

clearances, must be used for boiler installation.

Accessibility clearances may be achieved with the

use of removable walls or partitions.

• Boiler is approved for installation in closets and

on combustible floors.

This boiler shall NOT be

installed on carpeting.

• Install equipment in location which facilitates

operation of venting and combustion air intake

piping systems as described in this manual.

• Advise owner to keep venting and combustion

air intake passages free of obstructions. Both

venting and combustion air intake piping systems

connected to outdoors must permit flow through

piping systems without restrictions for boiler

operation.

• Keep boiler area clean of debris and free of

flammable and combustible materials, vapors and

liquids.

WARNING

Fire hazard. Do not install boiler on combustible

flooring or carpeting. Failure to follow these

instructions could result in death or serious

injury.

WARNING

Fire, explosion, and asphyxiation hazard.

Improper installation could result in death or

serious injury. Read these instructions and

understand all requirements before beginning

installation.

240013371 REV B, [10/01/2021]

Содержание MACF-115












































































































































Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды

UTICA BOILERS MACF-115, Руководство пользователя

Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды