u-blox ZED-F9P Скачать руководство пользователя страница 61

Страница: 61 / 267

u-blox ZED-F9P Interface Description - Manual

Advance Information

Name

Description

recordEnabled

1 = enable recording, 0 = disable recording

psmOncePerWak

upEnabled

1 = enable recording only one single position per PSM on/off mode wake-up period, 0 = disable once per wake-up

applyAllFilte

rSettings

1 = apply all filter settings, 0 = only apply recordEnabled

5.9.12 UBX-CFG-MSG (0x06 0x01)

5.9.12.1 Poll a message configuration

Message

UBX-CFG-MSG

Description

Poll a message configuration

Firmware

Supported on:
•

u-blox 9 with protocol version 27

Type

Poll Request

Comment

This message is deprecated in protocol versions greater than 23.01. Use

instead.

See the

Legacy UBX Message Fields Reference

for the corresponding configuration item.

Header

Class

Length (Bytes)

Payload

Checksum

Message Structure

0xB5 0x62

0x06 0x01 2

see below

CK_A CK_B

Payload Contents:

Byte Offset

Number

Format

Scaling

Name

Unit

Description

msgClass

Message Class

msgID

Message Identifier

5.9.12.2 Set Message Rate(s)

Message

UBX-CFG-MSG

Description

Set Message Rate(s)

Firmware

Supported on:
•

u-blox 9 with protocol version 27

Type

Get/Set

Comment

This message is deprecated in protocol versions greater than 23.01. Use

instead.

See the

Legacy UBX Message Fields Reference

for the corresponding configuration item.

Set/Get message rate configuration (s) to/from the receiver.
• Send rate is relative to the event a message is registered on. For example, if the rate of a

navigation message is set to 2, the message is sent every second navigation solution. For
configuring NMEA messages, the section

NMEA Messages Overview

describes Class and

Identifier numbers used.

Header

Class

Length (Bytes)

Payload

Checksum

Message Structure

0xB5 0x62

0x06 0x01 8

see below

CK_A CK_B

Payload Contents:

Byte Offset

Number

Format

Scaling

Name

Unit

Description

msgClass

Message Class

UBX-18010854 - R04

Advance Information

Page 53 of 259

Содержание ZED-F9P












































































































































































































































































Результаты поиска

Содержание ZED-F9P

Отзывы:

Похожие инструкции для ZED-F9P

Бренды по названию

Популярные бренды

u-blox ZED-F9P, Описание интерфейса

Результаты поиска

Содержание ZED-F9P

Отзывы:

Похожие инструкции для ZED-F9P

Бренды по названию

Популярные бренды