TYM T194 Скачать руководство пользователя страница 127

Страница: 127 / 169

7 - 3

Storage and diSpoSal

USe after long-term

Storage

Keep the following instructions

when using the Ride on lawnmower

after its long-term storage.
(1) Inspect the Ride on lawnmower

thoroughly before driving it.

() To keep performance and life of

the engine, idle the engine for

approx. 30 minutes after starting

it.

►

2. USage and diSpoSal

For engine lubrication, run the

engine at 1,500 ~ ,000 RPM for

5 to 10 minutes once a month.
Remove the key from the Ride

on lawnmower and store it sep-

arately.

•

note

If leaving the battery connected

to the Ride on lawnmower, turn

off its switch to cut electric pow-

er.
If wiring is damaged by rodents,

its short circuit can start a fire.

•

CaUtion

It is recommended to keep the fol-

lowings to protect the environment:
(1) Avoid overloading work as it can

lead to incomplete combustion

and emissions that can pollute

the air.

() When changing oil, including en-

gine oil, transmission fluid, hy-

draulic oil and coolant, be careful

not to spill it and discard used oil

according to the applicable law.

Used oil should be treated with

care and discarded properly as it

can contaminate soil and water.

(3) When this or other machine's life

is expired, do not neglect or dis-

card it on your own, but contact

your dealer so that the approved

service provider can discard the

machine according to the laws.

T194(K0) RIDE ON LAWNMOWER-영문-073 3

2018-06-27 오후 6:21:53

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды