TYM T194 Скачать руководство пользователя страница 57

Страница: 57 / 169

2 - 1

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

OPERaTING TIPS FOR POwER

STEERING wHEEl

►

Releasing the steering wheel

during driving can result in a

collision and rollover. Never re-

lease the steering wheel during

driving.

•

waRNING

(1) Operate the power steering

wheel only while the engine is

running. You may feel the steer-

ing wheel heavier with a low en-

gine speed.

(2) When an implement, such as a

loader, is attached to the front,

the steering wheel may be felt

heavy with the Ride on lawn-

mower stopped. If so, operate

the steering wheel while driving

the Ride on lawnmower at a low

speed.

(3) When the steering wheel is

completely turned to one end,

the safety valve is activated to

output the audible signal (relief

sound). When this sounds, avoid

using the steering wheel (O.K.

only for a short time). Also, never

turn the steering wheel com-

pletely continuously.

(4) Turning the steering wheel to its

end unnecessarily (with the Ride

on lawnmower stopped) can

wear tires rapidly.

(5) In winter, warm up the engine

sufficiently before use.

(6) When repairing components,

such as a pipe, make sure that

no foreign material enters the

system.

(7) The steering wheel can be op-

erated with a small amount of

force. Therefore, operate it with

care and keep your hands on it

at all times.

T194(K0) RIDE ON LAWNMOWER-영문-0219 19

2018-07-03 오후 3:49:38

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды