TYM T194 Скачать руководство пользователя страница 116

Страница: 116 / 169

6 - 16

Maintenance and service

checking electric Wir-

ing

(1) Loose wiring terminals can

cause contact failure and dam-

aged wiring can lead to perfor-

mance deterioration of electric

devices, short circuit and fire.

Replace or repair aged and

damaged wirings.

() If wiring sheath is peeled off,

wrap wiring with insulating tape.

(3) If fasteners or bands to fix wir

ings are damaged, fix wirings

with clamps.

() Have wiring checked by your

workshop once a year regularly

to avoid fire.

►

checking and replacing

fuse

(1) body fuse box

Fuses are installed in this Ride on

lawnmower to prevent any possible

accident in case of wiring circuit

malfunction.

►

T19O515A

Fuse Box

Open circuit

T5O5A

Normal

If the electric system is malfunction-

ing during driving, check for any

blown fuse.

①

Remove the cover of the fuse box.

②

Remove the blown fuse.

③

Fit a new fuse with the same ca-

pacity.

④

The function and capacity of each

fuse are indicated on the cover of

the fuse box.

If using fuses other than the

specified, wirings can be over-

heated, leading to a fire. Never

use a fuse with different capac-

ity. Also, never use a steel wire

or foil instead of a fuse.

•

Warning

T194(K0) RIDE ON LAWNMOWER-영문-0616 16

2018-08-13 오후 2:31:03

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды