TYM T194 Скачать руководство пользователя страница 52

Страница: 52 / 169

2 - 1

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

PaRkING bRakE PEDal

1. To engage the parking brake, at

first depress the brake pedals

down, and push the parking brake

pedal down. At this time, Release

the brake pedal first, then to be

locked the parking brake pedal.

2. To release the Parking brake, de-

press the brake pedals again.

►

The brake discs can be worn

prematurely if driving the ve-

hicle with the parking brake en-

gaged partially.

•

NOTE

When switching the driving

direction (forward/backward)

directly during driving, a shock

due to inertia can lead to an in-

jury. Therefore, switch the driv-

ing direction while the Ride on

lawnmower is stopped.
Switch the driving direction only

while you are on the driver's

seat.

•

waRNING

SUb SHIFT lEVER

The driving direction can be se-

lected between forward direction

and reverse direction using the

shuttle shift lever and range shift

lever.
Use the throttle lever to increase/

decrease the engine speed.

►

•

T19O122B

(Low speed)

(High speed)

(neutrality)

T19O141B

Parking Brake Pedal

T194(K0) RIDE ON LAWNMOWER-영문-0214 14

2018-07-03 오후 3:49:26

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Бренды по названию

Популярные бренды