manualshive.com logo in svg

TYM T194, Руководство пользователя

Поделиться
Скачать
TYM T194 Скачать руководство пользователя страница 156

12

 - 

WARRANTY

YANMAR WARRNTIes

■

 

YANMAR lIMITeD WARRANTY

What is Covered by this Warranty?

YANMAR warrants to the original retail purchaser that a new YANMAR TNV common rail series industrial engine 
will be free from defects in material and/or workmanship for the duration of the warranty period.
Note:  YANMAR  engines  may  be  equipped  with  external  components  including,  but  not  limited  to:  wiring 

harnesses,  electrical  devices,  control  panels,  radiators,  air  filters,  fuel  filters,  and/or  exhaust  systems 
that  are  supplied  and/or  installed  by  manufacturers  other  than YANMAR.  For  warranty  information  on 
such external components, please contact the machine or component manufacturer directly or see your 
authorized YANMAR dealer or distributor.

This warranty is provided in lieu of all other warranties, express or implied. YANMAR specifically disclaims
any implied warranties of merchantability or fitness for a particular purpose, except where such disclaimer
is prohibited by law. If such disclaimer is prohibited by law, then implied warranties shall be limited in
duration to the life of the express warranty.

how long is the Warranty Period?

The YANMAR  standard  limited  warranty  period  runs  for  a  period  of  twenty-four  ()  months  or  two-thousand 
(000) engine operation hours, whichever occurs first. An extended limited warranty of thirty-six () months or 
three thousand (000) engine operating hours, whichever occurs first, is provided for these specific parts only: 
the  cylinder  block,  cylinder  head,  crankshaft  forging,  connecting  rods,  flywheel,  flywheel  housing,  camshaft, 

T194(K0) RIDE ON LAWNMOWER-영문-122   2

2018-06-28   오전 10:28:16

Содержание T194










































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды