TYM T194 Скачать руководство пользователя страница 115

Страница: 115 / 169

6 - 15

Maintenance and service

436

<charging>

①

Turn the ignition switch to the

"OFF" position and remove the

battery from the Ride on lawn-

mower.

②

Charge the battery in a well-

ventilated area.

③

Charge the battery with the nor-

mal procedures and avoid quick

charging.

④

Turn the charger switch OFF and

connect the cables to the nega-

tive and positive battery termi-

nals correctly.

⑤

When using a charger, its charg-

ing current should be below 10 A.

T5O51A

Negative (-)

terminal (black)

Positive (+)

terminal (red)

juMp start

①

Turn off all electric devices.

②

Connect the positive terminal of

the normal battery to the positive

terminal of the discharged bat-

tery with the jump cable.

③

Connect the negative terminal of

the normal battery to the engine

body of the Ride on lawnmower

for the discharged battery with

the jump cable.

►

T5O5A

④

Firstly, start the engine of the

vehicle with the normal battery.

Then, start the engine of the

Ride on lawnmower with the dis-

charged battery.

⑤

After the engine is started, dis-

connect the negative cable first.

Then, disconnect the positive

cable.

⑥

Charge the discharged battery

for approx. 30 minutes after the

engine is started.

Make sure to connect the posi-

tive terminal first and connect

the negative terminal to the

engine body of the Ride on

lawnmower with the discharged

battery.

•

Warning

T194(K0) RIDE ON LAWNMOWER-영문-0615 15

2018-08-13 오후 2:31:01

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Бренды по названию

Популярные бренды