TYM T194 Скачать руководство пользователя страница 51

Страница: 51 / 169

2 - 1

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

THROTTlE lEVER

It is used to adjust the engine speed
like the throttle pedal.

Pushing : increasing speed

Pulling : decreasing speed

►

Throttle lever

bRakE PEDEl

The brake pedal is located on the

LHS of the operator.
It is used for two functions.
- To stop the Ride on lawnmower
- To release cruise control

►

Brake pedal

Never use it unless working in

a field. It can lead to speeding

and an accident.

•

waRNING

T19O119A

DRIVING SPEED CONTROl

PEDal

When depressing the forward driv-

ing speed control pedal, forward

driving is selected. Reverse driving

is selected by depressing the re-

verse driving speed control pedal.

When releasing the speed control

pedal, it is returned to the neutral

position and the Ride on lawnmower

is stopped.

►

Driving speed

control pedal (forward)

Driving speed

control pedal (backward)

T19O120A

T19O121A

T194(K0) RIDE ON LAWNMOWER-영문-0213 13

2018-07-03 오후 3:49:23

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Бренды по названию

Популярные бренды