TYM T194 Скачать руководство пользователя страница 78

Страница: 78 / 169

3 - 18

OPERATiOn

It is not recommended to use

a pressure washer to clean the

mower assembly. High pressure

water may cause damage to

spindles, pulleys, belts, or bear-

ings shortening life and reduc-

ing serviceability.

•

CAUTiOn

TK0303A

TK0304A

Life of the mower depends upon the

maintenance given. Proper lubrica-

tion is very important.
Always lubricate the deck and lift

components before operation.
Always wipe the fittings to be lu-

bricated with a clean cloth before

greasing. Dirt injected into the fitting

will cause damage to the machined

parts.
Use SAE Multi-purpose lithium base

grease on all lubrication locations

shown below. Remember to wipe

away excess grease, which has

built up around parts.

Lubricate grease fittings after every

50 hours of operation.
Miscellaneous working parts not

provided with lubrication fittings

should be oiled daily with a good

grade of lubricating oil.

14. LUBRiCATiOn

T194(K0) RIDE ON LAWNMOWER-영문-0318 18

2018-09-11 오후 5:27:27

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды