TYM T194 Скачать руководство пользователя страница 44

Страница: 44 / 169

2 -

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

HazaRD FlaSHER SwITCH

This switch can be used to warn

other vehicles when malfunction

occurs in the Ride on lawnmower

while driving on a public road. When

pressing the switch once, the left

and right hazard warning lamps

blink. Pressing the switch again

turns off the lamps.

►

Hazard flasher switch

(2) Turn signal lamp operation
The turn signal lamps can be op-

erated with the main switch in the

"ON" position.

This lever is not automatically

returned to the neutral position.

Therefore, set it back to the

neutral position after turn.

•

NOTE

Left turn

Turn the turn signal switch counter-

clockwise. Then, the left turn signal

lamp and the left turn signal indica-

tor on the instrument cluster blink.

Right turn

Push the turn signal switch clock-

wise. Then, the right turn signal

lamp and the right turn signal indi-

cator on the instrument cluster blink.

•

T19O114A

T194(K0) RIDE ON LAWNMOWER-영문-026 6

2018-07-03 오후 3:49:12

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды