TYM T194 Скачать руководство пользователя страница 63

Страница: 63 / 169

OPERATiOn

3 - 3

2. THE RidE On MOWER

1. Read, understand and follow all

instructions in the manual and

on the machine before starting.

Failure to do so could result in

serious injury or death and equip-

ment damage. Keep this manual

in a safe place for future and

regular reference and ordering

service parts.

. Read and understand all Safety

Precautions in the Ride on Mower

Operator's Manual.

3. Allow only responsible operators

familiar with the instructions to

operate the machine. Know the

controls and how to stop Ride on

Mower engine and mower quickly

in an emergency.

4. Ride on Mower must be equipped

with Rollover Protective Sys-

tem (ROPS) and seat belt for all

mower operations foldable ROPS

systems locked in the up position

at all times when operating the

mower. Falling off or overturn-

ing a Ride on Mower can result

in death from being run over or

crushed.

5. Always wear seat belt on Roll-

over protective System (ROPS)

equipped Ride on Mowers.

6. Wear personal protective equip-

ment (PPE), such as, but not lim-

ited to, protection for eyes, ears,

lungs, head, hair, hands and feet

when operating, servicing, or

repairing the equipment. Avoid

wearing loose clothing or jewelry

that may catch and entangle on

entangle in moving parts.

7. Stop Ride on Mower engine,

place in neutral, engage park-

ing brake, lower mower deck to

ground, stop all moving parts,

remove ignition key to prevent

unauthorized person.

8. Never leave the Ride on Mower

with the mower blades rotating,

with the Ride on Mower in mo-

tion, or the engine running.

9. Use fender hand holds and steps

when mounting and dismounting

Ride on Mower to prevent falls.

Keep steps and Operator's plat-

form clean and free of debris.

10. Move and turn Ride on Mower

at low speeds. Avoid erratic op-

eration and excessive speed.

11. Keep the Ride on Mower in gear

when traveling down hill.

1. Do not mow near drop-offs,

ditches, or embankments. The

Ride on Mower could suddenly

overturn if a wheel travels over

the edge of a ditch, or if an edge

caves in.

13. Add wheel ballast for stability

when operating on slopes. Pay

extreme care when operating on

slopes to maintain stability.

T194(K0) RIDE ON LAWNMOWER-영문-033 3

2018-09-11 오후 5:27:07

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды