TYM T194 Скачать руководство пользователя страница 16

Страница: 16 / 169

- 1

SAFeTY PReCAUTIONS

T72O217A

Do not start the Ride on lawnmow-

er in an enclosed building unless

the doors & windows are open for

proper ventilation, as Ride on lawn-

mower fumes can cause sickness

or death. If it is necessary to run an

engine in an enclosed area remove

the exhaust fumes by connecting

exhaust pipe extension.

WORK IN VeNTILATeD AReA

1. The Ride on lawnmower can start

even if the transmission is en-

gaged position causing Ride on

lawnmower to runaway and seri-

ous injury to the people standing

nearby the Ride on lawnmower.

2. For additional safety keep the pull

to stop knob (Fuel shut off con-

trol) in fully pulled out position.

Transmission in neutral position,

Foot brake engaged and PTO le-

ver in disengaged position while

attending to Safety Starter Switch

or any other work on Ride on

lawnmower.

RIDe ON LAWNMOWeR RUN-

AWAY

1. Brake operated safety switch is

provided on all Ride on lawn-

mowers which allow the starting

system to become operational

only when the Brake pedal is fully

pressed.

2. Do not by-pass this safety starter

switch or work on it. Only Autho-

rized Dealers are recommended

to work on safety starter switch.

3. On some models Safety Starter

switch is provided on transmis-

sion High-low shifter lever and in

PTO shifter lever. The Ride on

lawnmower can be started only if

High-low shifter lever is in neutral

position.

Safety Starter Switch is to be

replaced after every 2.000

hours/4 years, whichever is

earlier.

•

CAUTION

SAFeTY STARTeR SWITCH

T194(K0) RIDE ON LAWNMOWER-영문-0116 16

2018-08-13 오후 4:23:12

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды