TYM T194 Скачать руководство пользователя страница 54

Страница: 54 / 169

2 - 1

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

< Examples of useful conditions

of differential lock >

①

One wheel slips or Ride on lawn-

mower cannot be driven forward

when moving into/out of a field.

②

A wheel slips during work requir-

ing traction, such as plowing.

③

One wheel is stuck into a soft

field and can't escape.

FRONT wHEEl DRIVE lE-

VER (4wD)

Front wheel drive lever is located

below the LHS of the Operator.
In the ON position the front wheels

are engaged and in the OFF posi-

tion they are disengaged.
Engage & disengage the front wheel

drive with the front wheels in the

straight position and at low speed.

►

Front wheel drive

lever(4WD)

< Examples of useful conditions

of 4wD >

The 4WD can be used under the

following conditions

①

When cultivating in a field.

②

When traction is required on a

slope, in a wet field or for towing

a trailer.

③

When working in a wet or sandy

field.

④

When cultivating on firm soil

with a rotavator to prevent the

Ride on lawnmower from being

pushed forward.

⑤

When driving into/out of a field or

going over a field bank.

T19O125A

T194(K0) RIDE ON LAWNMOWER-영문-0216 16

2018-07-03 오후 3:49:32

Содержание T194










































































































































































Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды

TYM T194, Руководство пользователя

Результаты поиска

Содержание T194

Отзывы:

Похожие инструкции для T194

Бренды по названию

Популярные бренды